0.56 LEDs
General Features
External transmitters or signal conditioners can be eliminated by
Specifications
Input Specs: Depends on Input signal conditioner A/D Converter: 14 bit single slope Accuracy: (005% of reading + 2 counts) Temp. Coeff: 100 ppm/C (Typical) Warm up time: 2 minutes Conversion Rate: 10 conversions per second (Typical) Digital Display: 4 digit 0.56" LED red (std), green (optn)
Range 1999 to 9999 counts
Bargraph Display: 101 segment 235o circular red (standard),
Green (optional) or tricolor (optional) LED
Polarity: Assumed positive Displays negative Decimal Selection: Front panel button selectable, XXXX Positive Overrange: Bargraph and top segments of digital display
flash
Negative Overrange: First segment of bargraph and bottom seg-
ments of digital display flash
Relay Output: Two 9 Amp Form C relays, two 4 Amp Form
A relays or 4 x 4 Amp Form A relays
Analog Output: Isolated 16 bit user scalable mA or V OIC (mA out) 4-20 mA @ 0 to 500 max loop resistance OIV (volts out) 0-10 V DC @ 500 or higher resistance Power Supply: AC/DC Auto sensing wide range supply PS1 (std) 85-265 VAC / 95-300 VDC, 50-400Hz 4.2W PS2 18-48 VAC / 10-72 VDC, 50-400Hz 42W Operating Temp: 0 to 50C Storage Temp: 20C to 70C Relative Humidity: 95% (non condensing) Case Dimensions: Bezel (4.48"x4.48") 113.8x113.8mm
Depth behind bezel (4.23") 107.46 mm Plus (048) 1224 mm for connectors
Weight: 16 oz, 1lb 4 oz when packed
direct connection of the sensor output to more than
40 Plug-in Input Signal Conditioners that include:
AC/DC Current
AC/DC Voltage
Load Cell
Pressure
Process
Prototype
Resistance
Temperature
4 to 20 mA
Optional isolated 16 bit analog output. User or factory scalable to 4
to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span from one count to the full scale range of 1999 to 9999 (12000 counts).
A Programmable Tricolor (Red-Green-Orange) or mono color (red or
green), 101 segment high brightness bargraph.
Red 4-digit LED display with a range of -1999 to 9999
(12000 counts). Optional green digital display.
Front panel LED annunciators provide indication of setpoint status.
Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A relays available.
Auto-sensing AC/DC power supply. For voltages between
85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC (PS2).
24 V DC excitation is available to power external 4/20mA transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors.
Provision to connect an external programming lockout switch.
Provision for external DIM switch to reduce the brightest
display setting by 50%.
Automatic intelligent averaging, smooths noisy signals while providing a fast display response to real level changes.
Software Features
The bargraph can display, full scale, any desired portion of the digital reading.
Setpoint 1 has delay-on-make
and delay-on-break plus
a special pump on pump off mode that creates a Hysteresis Band between SP1 and SP2.
Four programmable setpoints with adjustable Hysteresis.
Bargraph center zero function.
Relay activation can be selected to occur above (hi) or below
(Lo) each setpoint.
Digital display blanking.
Decimal point setting.
Four-level brightness control
Bargraph Center Point Display Mode Selection... 6 Bargraph Color Programming Mode........ 9 Case Dimensions....................... 7 Component Layout..................... 11 Connector Pinouts..................... 10 Connectors........................... 11 Controls and Indicators.................. 2 Decimal Point and Brightness Selection..... 5
Table of Contents
Digital Span Selection for Display.......... 5 Digital Span Selection for Analog Range Output... 6 Functional Diagram.................... 10 General Features....................... 1 I-Series Input Signal Conditioning Modules... 12-14 Input Module Calibration Procedures...... 16 Input Module Component Glossary........ 15 Installation guidelines................... 17 Ordering Information................... 18
Pin Descriptions....................... 10 Programming Conventions................ 2 Setpoint Setting & Relay Configuration Mode.... 8-9 Software Features...................... 1 Software Logic Tree..................... 3 Specifications.......................... 1 Two Point Analog Range Setting & Calibration.... 7 Two Point Digital Calibration Mode......... 4
Page 1
Texmate is an American manufacturer of high durability industrial grade panel meters, bar graphs, and transducers. Texmate's meters are frequently equipped with relays and various signal outputs for industrial automation applications and are known for their extremely long service life.