TIGER FAMILY
The Tiger 320 Operating System supports an easy to use PC based Configuration Utility Program, which can be downloaded FREE from the web, and programming from front panel buttons.
The T Version supports custom macro programs that can be easily produced with the Tiger 320 Macro Development System (available FREE on the web). The Development System enables programs to be written in BASIC, which can utilize any combination of the hundreds of functions and thousands of registers embedded in the Tiger 320 Operating System.
Red, green, or superbright red 14-segment, 0.56 high LEDs with full support for 14-segment alphanumeric text.
The meter comes with two extra buttons, F1 and F2, that
are available to access functions via macro.
Brightness control of LED display from front panel buttons.
Modular construction with more than 120 interchangeable input signal conditioners and more than 25 interchangeable I/O modules.
Up to 4 input channels with cross channel math for multi-
channel processing.
For applications where sensor excitation is required, modules are provided with 5V, 10V or 24 V DC voltage outputs.
On demand tare, calibration and compensation can be initi-
ated by the front panel program button.
Autozero maintenance for super stable zero reading is pro-
vided for use in weighing applications.
Programmable input averaging and smart digital filtering for
quick response to input signal changes.
Display text editing. Customize display text for OEM appli-
cations.
Scrolling display text messaging on T meters with macros.
Auto-sensing high voltage or optional low voltage AC / DC
power supply.
Serial output options include RS-232, RS-485, ModBus, Ethernet, DeviceNet or direct meter-to-meter communications.
Single or dual 16-bit
Isolated Analog Outputs.
Programmable 0~4 to 20mA or 0 to 10V for retransmission, 4-20mA loops to drive valve actuators, remote controllers & displays, multi-loop feedback and PID output. Scalable from
1 count to full scale.
Dual independent totalizers to integrate input signals.
6 super smart, independently programmable setpoints with
8 selectable functions, including latching, deviation, hysteresis, register resetting, tracking and dual PID. Plus 7 programmable timer modes on all 6 setpoints.
Setpoint tracking, setpoint latching and manual relay reset.
Setpoints activated from any input, any register in the meter
or from any digital input.
Plug-in I/O modules include electromechanical or solid state relays, logic outputs or open collector outputs. 6 inputs & 16 outputs of opto-isolated I/O can be connected to an external DIN Rail terminal block module.
Internal program safety lockout switch to prevent tampering.
Peak & valley (max & min) with front panel recall and reset.
Real time clock with 15 year Lithium battery backup.
Data logging within the meter (up to 4000 samples with
date/time stamp).
Optional NEMA-4 front cover.
TIGER FAMILY: More than 120 different Plugin I-Series Input Signal Conditioners are approved for the Tiger Family of meters.
See I-Series Input Signal Conditioning Modules Guide (Z87) for an up-to-date list.
General Features...................1 Specifications......................2 Tiger 320 Series Literature Overview...3 Tiger 320 Series System Overview...4-5 Planning to Use the Tiger 320.......6-8 Block Diagram of Tiger 320 Structure...9 Configuration Utility Program.........10 Custom Macro Program............11 Index.........................12-13
Controls & Indicators............14-15 Front Panel Configuration & Setup....16 Front Panel Programming Codes...17-18 Initial Setup Procedures..........19-20 Display Brightness.................20 Calibration Modes..............21-24 Programming Procedures........25-37 Setpoint Programming Mode......38-43 Registers........................44
Functional Diagram................45 Connector Pinouts.................45 Carrier Board Output Pins...........46 Relay and Logic I/O Modules........46 Component Layout & Ext. Devices...47-48 I-Series Input Modules...........49-55 Ordering Information............56-58 Custom Faceplates................59 Case Dimensions.................60
Specifications
Display
Digital Display: 14-segment alphanumeric, 0.56 (14.2 mm) LEDs.
Display Color: Red (std). Green or Super-Bright Red (optional).
Digital Display Range: -199999 to 999999 Update Rate: 3 to 10 times per second Display Dimming: 8 brightness levels. Front Panel selectable Scrolling Display Text Messaging: Full alphanumeric text characters supported on T Version with macros.
Polarity: Assumed positive. Displays - negative Decimal Point: Front panel, user selectable to five positions.
Annunciators: 6 red LEDs on front panel; one per setpoint.
Overrange Indication:
Underrange Indication:
Front Panel Controls: PROGRAM, UP, DOWN, F1 and F2.
Operating System (Tiger 320)
Processor: 32 bit with floating point maths (18.4 MHz).
Flash Memory: 64k, 4k for use by custom macros.
RAM: 1.25k and FeRAM 4k.
EEPROM: E Version 4k standard, T Version 32k standard. Memory upgrades available to 32k for LIN Tables and 1MB for Data Logging and custom macros.
Registers: 6144 registers comprised of 8, 16 or 32 bit signed, unsigned or floating point registers, implemented in a combination of RAM, FeRAM, Flash and EEPROM.
Internal communication BUS: 32 bit I2C BUS Real Time Clock (option): Year:Month:Date:Hour:Minute:Second with 15 yr Lithium battery backup.
Configuration: Supports Front Panel Programming Codes and a PC-based Configuration Utility Program, which may be downloaded free from the web. T Version also supports custom macros.
Development System for Custom Macros
The Tiger 320 Macro Development System, which may be downloaded free from the web, can be used to create powerful macro software that allows Tiger 320 T Versions to be easily customized to suit any proprietary OEM application (see page 11).
Installed Application Software Includes
Counter Functions: Two built-in counters. UP counters, DOWN counters, UP/DOWN counters and high speed quadrature counters.
Data Logging: Logging with a date/time stamp, initiated at timed intervals, by activation of a setpoint, or manually. Data stored in internal 1MB EEPROM or in a removable 4 to 128M Flash Card Memory Module. Endless loop recording is supported.
Input Compensation: Provides compensation to the primary input channel (CH1) via channels 2, 3 or 4.
Linearization: 4 selectable 32 point or one 125 point flexible linearization tables are provided.
Logic I/O: 28 Macro programmable I/O ports supported.
Manual Loader: Front panel adjustable, 4 to 20mA or 0 to 10V isolated analog output.
Math Functions: Cross channel math functions to calculate the sum, difference, ratio or the product of two inputs.
On Demand Functions: Tare, compensation and calibration.
Peak and Valley: The meter can retain peak and valley (min/max) information and recall this on the front panel.
Remote Setpoint Input: Remote setpoint input via channel 2.
Serial Output Protocols: Selectable communication modes include ASCII, Modbus (RTU), Master Mode (for meter to meter communication) and an Epson compatible printer driver. DeviceNet and Ethernet optional output carrier boards are also supported.
Setpoint Functions: Six super smart setpoints with fully configurable hysteresis, on and off delays, one shot, pulse and repeat timers, latching, dual PID, setpoint tracking, resetting of registers, initiating of logging and printing.
Signal Conditioning Functions: Averaging, smart filter, rounding, square root,auto zero maintenance.
Timer: Timer functions supported in either time-up, time-down, or real-time clock modes.
Totalizer: Two totalizers for running total and batch totals of a process signal that can be accumulated over time.
Inputs
Inputs Available: More than 120 single, dual, triple and quad input signal conditioners available covering all types of analog, digital and mixed input signals (see page 49).
Accuracy: Tiger 320 PMCs enable the user to establish any degree of system accuracy required. Built-in compensation and linearization functions enable system accuracies of the order of 0.0001% of reading for analog inputs. Stop -Start time resolution from 1sec to 0.7nsec. Digital input and pulse counts 1 count.
A/D Convertors: A Dual Slope, bipolar 17 bit A/D is provided as standard on the main board. SMART modules can have 24 bit or 16 bit Delta-Sigma A/D convertors that utilize the internal I2C BUS.
Temperature Coefficient: Typically 30ppm/ C. Compensation can be utilized to achieve system temperature coefficients of 1ppm.
Warm Up Time: Up to 10 minutes, depending on input module.
Conversion Rate: Typically 10 samples per second. However, SMART input modules are available that can convert at 60, 240, 480 or 960 samples per second.
Control Output Rate: Can be selected for 100msec or 10msec.
Some SMART modules have SSR outputs that react within 1.2msec.
Excitation Voltage: Depends on input module selected. Typically, 5V, 10V or 24VDC is provided.
1. Standard Carrier Board:
Is available without a serial output, or with either an isolated RS-232 or an isolated RS-485 (RJ-6 socket).
2. DeviceNet Carrier Board: 5 pin 3.5mm screw terminal.
3. Ethernet Carrier Board: 10/100Base-T Ethernet (RJ-45 socket).
Two Isolated Analog Output Options: Mounted on any carrier board.
1. Single Analog Output: Fully scalable from 4 to 20mA or 0 to 20mA
(or reverse) and selectable for 0 to 10VDC (or reverse).
2. Dual Analog Output: Fully scalable from 0 to 10VDC (or reverse).
Accuracy: 0.02% FS. Analog Output Specifications:
Resolution: 16-bit Delta-Sigma D/A provides 0.4A on current scaling, 250V on voltage scaling. Compliance: 500 maximum for current output. 500 minimum for voltage output. Update Rate: Typical 7 per second. Step Response: Typical 6msec to a display change. Scalable: From 1 count to full scale.
Seven I/O Modules: Plug into any carrier board from rear.
1. Four Relay Module: Available in six combinations from one relay up to a total of two 10A Form C Relays* and two 5A Form A Relays**.
2. Four Relay Module: Available with one to four 5A Form A Relays**.
3. Six Relay Module: Available with five or six 5A Form A Relays**.
10A 240VAC~1/2 HP, 8A
*Form C Relay Specifications:
24VDC. Isolation 3000V. UL and CSA listed. **Form A Relay Specifications:
Isolation 3000V. UL and CSA listed.
5A 240VAC, 4A 24VDC.
4. Four Solid State Relay (SSR) Module: Available with one to four independent (210mA DC only) or (140mA AC/DC) SSRs (400V max).
5. Six Output 5VDC / TTL or Open Collector: Available with 0 to 5V
or 0 to V+ (40VDC max).
6. Opto Isolated I/O Module: Available in either 6 Outputs & 6 Inputs, or
16 Outputs and 6 Inputs. For connection to an external breakout box.
7. Flash Card Memory Module: Available with 8 or 16 MB memory.
Power Supplies
Approvals
CE: As per EN-61000-3/4/6 and EN-61010-1.
(cid:3)(cid:3)The Tiger 320 Series, Modular Literature system, makes it easy to select detailed information about those specific functions required for your application and the Configuration of the Tiger 320 you intend using.
Copies of all Data Sheets / User Manuals and Supplements can be viewed page-by-page and/or downloaded from the document server on our website.
Programming Code Sheet
Generic to all Tiger 320 Series models, the Programming Code Sheet is a quick reference document that allows you to quickly view the meters manual programming codes.
Shipped with each product ordered, copies are also available on request, or can be viewed and downloaded from the document server on our website.
Model Specific Data Sheet / User Manual
Specific to each 320 Series meter model, the data sheet / user manual describes the basic functions of the meter and how to configure the meter for these functions.
Shipped with each product ordered, copies are also available on request, or can be viewed and downloaded from the document server on our website.
The model specific data sheet / user manual contains:
Technical Specifications
Front Panel Button Manual
Overview of Tiger 320 Series
Programming Codes Overview
Software and Hardware
Programming Procedures
Planning Guide
Functional Diagram and
Block Diagram of the Tiger
320 Software and Hardware
Configuration Utility Program
Custom Macro Programming
Front and Rear Panel
Controls
Pinouts
Hardware Layout and Available
Input and Output Modules
Meter Options, and Custom
Faceplates
Ordering Information
Supplements to Data Sheet / User Manual are Generic to all Tiger 320 Models
Generic to all Tiger 320 Series models, each supplement provides in-depth technical and procedural information on all individual meter modules, functions, or applications.
Listed are the supplements which are currently available:
Specific supplements are
shipped with each product ordered to suit our customers application. Copies are also available on request, or can be viewed and downloaded from the document server on our website.
(cid:2)(cid:2)Advanced Calibration and On DEMAND
Mode
(cid:2)(cid:2)Analog Output Modules
(cid:2)(cid:2)BASIC to Tiger 320 MACRO-Language
Program Development System, Compiler and Tutorial
(cid:2)(cid:2)Configuration Utility Program (Runs on PC) (cid:2)(cid:2)Linearizing Functions
(cid:2)(cid:2)Meter Registers (for Macro Programming) (cid:2)(cid:2)Serial Communications Output Modules (cid:2)(cid:2)Setpoints & Relays
(cid:2)(cid:2)Totalizing & Batching Functions
Other Tiger 320 Series Related Literature
Tiger 320
Functional Overview
Tiger 320
Application Examples
I-Series Input Signal
Conditioning Modules
Meters By the
Case Size
A virtual toolbox of selectable and programmable application software functions are embedded in the Tiger 320 Operating System. They integrate seamlessly with a truly vast array of modular input and output hardware options.
Embedded Application Software Includes:
Multi-channel Inputs In Many Combinations
Full Floating-point Maths
Cross Channel Math (A+B, A-B, AxB, A/B)
Square Root, Inverse and Log of Input
4 x 32 Point Or 1 x 125 Point Linearization Table
Smart Auto Zero with Programmable Capture Band, Rate
of Change and Aperture Window for Weighing Applications
Set Tare Reset Tare for Batching
Smart Quick Response Averaging
Smart Timer and Time Integration Functions
Time and Event-based Sequencing
Polynomial Calculations
Remote Reset of Any Function
Dual Totalizers
Dual PID
Data Logging and Memory Options Up to 1MB of non-volatile on-board memory can be installed for (Black Box) endless loop recording. Up to 4000 data records can be continuously stored to provide before and after analysis of any process fault condition.
Data log from 4 channels.
Data log from 2 channels with date & time stamp.
Log / print from setpoint
A Plug-in I/O Module is available with removable Flash Card Memory for high-capacity or long-term data logging.
or timer.
Flash Cards are
available from 4
to 128 Meg.
Optional Real-time clock
with date and time stamp.
15 year lithium battery.
Powerful Custom Macro Programming Capability Texmates BASIC to Tiger 320 Macro-language Compiler can quickly Convert your special metering, control and automation ideas into reality.
This powerful easy to use development system enables programs to be written in BASIC utilizing any combination of the hundreds of functions and thousands of registers embedded in the Tiger 320 Operating System. When your BASIC program is compiled into the Tiger 320 Macro-language it is error checked and optimized. There are also numerous offthe-shelf application specific programs available. Many only need the blanks to be filled in to use them and this does not require any knowledge of BASIC.
Scrolling annunciator messages can be programmed to appear with any setpoint activation, selected events or logic inputs.
Programmable Front Panel Controls
The front panel buttons can be used to control or program any standard functions.
They can also be programmed to only access and display specifically designated functions, such as Tare, Auto-Cal or Print on Demand.
PC Programming
Program the meter from a PC with Texmates easy to use Tiger 320 Configuration Utility Program.
144x72mm 9/32 DIN
Single or multiple LED or LCD displays Numeric, Alpha Numeric and Bargraph
48x96mm1/8 DIN
96x48mm1/8 DIN
36x144mm
9/64 DIN
648x144mm 4LED
Remote Display
5 or 6 digit Driven by RS485
from any Tiger 320
6 Inputs & 16 Outputs or 6 Inputs & 6 Outputs
Fully Programmable
Connects to DIN Rail terminal block module with 3M IDC cable
Three logic level inputs are provided on the module input header and three rear input pins are provided that can be programmed to STOP/START/RESET almost any function including: set tare, reset tare, relays, totalizers, print output, data logging, peak, valley, or any register from an external contact closure.
Serial module
Analog Output module
Output Module Carrier Board
Scrolling Annunciator up to 99 Characters long is available on all 6 setpoints for Alphanumeric Displays with Fill-in-theblanks Macro.
Dual PID
Dual PID
Activation
Relay Latching
Single
Dual
RS-232
Serial Printer Output
Smart printer driver makes simple serial printers look intelligent.
0 ~ 4-20mA or 0-10V Programmable 0~4 to 20 mA or 0 to 10 V for retransmission, 4-20 mA loops, drive valve actuators, remote controllers & displays, multi-loop feedback and PID output.
0-10V & 0-10V
Auto-sensing AC/DC Power Supply
High Efficiency CE tested Auto Sensing AC/DC power supplies.
Standard 85-265 Volt AC / 95-370 Volt DC.
Low Voltage 9-32 Volt AC / 10-60 Volt DC.
RS-485
Selectable Communication
Modes include:
ASCII
Modbus
Ethernet (TCP/IP)
Devicenet (with optional carrier board installed)
Interface directly with PCs (using Windows terminal program), PLCs, or any Epson compatible serial printer.
Meter to Meter Communication.
Direct meter to meter communication enables two meters to share data and resources.
Choose from over 120 different single, dual, triple
and quad input signal conditioners.
Over120Single-Input,Dual-Input,Triple Input and Quad-Input signal conditioners work with the Tiger 320 series
Mixed function and smart modules with their own A/Ds, co-processors, SSRs and I2C Bus outputs are available to suit almost any application.
A combination of modular hardware and software resources enable Tiger 320 Series Programmable Meter Controllers
(PMCs) to be easily configured as a cost effective solution for the most simple or the most complex of applications.
A review of your Projects objectives, its physical layout, the proposed sensors and control outputs will enable you to select the optimum configuration of the Tiger 320 PMCs unique hardware and software capabilities.
Input Signals & Sensors
4-20 mA or Sensor Direct Unless sensors are located at a far distance, the greatest accuracy and best performance is usually obtained by connecting sensors directly to the Tiger 320, which will then function as the primary measurement device.
There are more than 120 Tiger compatible input signal conditioning modules, with the appropriate excitation outputs, to suit almost any type of sensor or combina-
tions of up to 4 sensors.
In most cases, sensors with a 4-20 mA output are more costly, and when a separate 4-20 mA transmitter is used, signal conversion, drift, and calibration inaccuracies are introduced.
Some Tiger input modules combine direct sensor inputs with 4-20 mA inputs, enabling both local and far distant sensor inputs to be combined.
Sensor Linearization or Compensation The performance of many sensors can be greatly enhanced or expanded with linearization and or compensation. Sensors may be compensated for temperature, frequency, altitude, humidity and mechanical position, to name just a few parameters.
Tiger PMCs with 32 kilobits or more of memory provide up to four 32-point user defined linearization tables or one combined 125-point table.
Many compensation methods can be implemented with the standard cross channel math capabilities of the Tigers 32-bit operating system. Complex three-dimensional compensation can also be implemented using the powerful macro programming capability.
The serial number and calibration date of a sensor can be loaded into the meter. The serial number, linearization tables, and compensation factors of a newly calibrated sensor can then be saved for future reloading, either serially through a PC or directly through the web via an Ethernet port.
Although there are numerous input modules with combinations of various input signals, some inputs such as watts or pH are provided on input modules dedicated to a single function. Combining these inputs with each other signals two or more Tiger meters can serially communicate, and be configured to share their data and processing resources.
Display Options
Tiger PMCs have a large range of display options, including digital and alphanumeric LCDs, LEDs and Touch Panel HMIs.
LED or LCD Displays LED displays are a lower cost and popular display option.
They operate over the largest temperature range, have better viewing angles and viewing distances, and have the longest operational life. However, red LEDs are difficult to read in direct sunlight without a shade hood and consume more power. Green LEDs and backlit LCD displays can be more easily read in direct sunlight.
The Tiger range can be ordered with red or green LEDs.
LCD displays are also available, with or without backlighting.
Numeric or Alphanumeric Displays Generally, numeric displays are a lower cost option than alphanumeric displays. The Tiger range supports a full 7segment numeric and 14-segment alphanumeric alphabet of English letters and Arabic numerals. Where complex text messaging or alarm annunciation is required, we recommend using the 14-segment alphanumeric option.
Single or Multiple Display The Tiger meter has four input channels and can be configured to display many different inputs or results. These can be viewed constantly on the operational display, or on demand in one of the view modes by pressing a button. Some applications require multiple values to be displayed simultaneously. With single, dual, or triple displays, and single displays with 51 or 101-segment bargraph combinations, we have a large range of display options to choose from.
Tiger meters can communicate with each other to share their data and processing resources and be stack or twin mounted to provide a wider range of display options.
Stack mounting
for greater display
options
Twin or triple mounting for greater display options
Push Button or Membrane Touch Pads Tiger PMCs are shipped as standard with high usage hard plastic push buttons. An optional clear lens cover that opens on a cam hinge with a key lock can provide full NEMA 4 or IP65 dust and water proofing. Alternatively, an optional membrane touch pad faceplate can be ordered.
Faceplates can be custo suit any tomized OEM application, and
be quickly produced in large or small quantities for push buttons or membrane touch pads.
Electromechanical Relays or Solid State Control Outputs
Tiger PMCs have a wide selection of control outputs to chose from. The decision on which control output to choose depends on the current and the switching frequency.
Electromechanical relays are a popular choice for most control outputs. Tiger output modules are available with combinations of two 10 amp form C and two to six 5 amp form A relays that can be used to directly drive fractional HP motors or actuators.
The limitation of electromechanical relays is switching speed. If a relay needs to operate in less than 30 mS, or be cycled faster than.5 cpm, it is advisable to select an output module with solid state relays (SSR) or open collector outputs (OC), that can drive external high current SSRs.
PID or On/Off Control Depending on the process to be controlled, either PID or on/off control should be selected. If the process variables are reasonably consistent, then the on/off control is generally more than adequate and easier to implement. Super smart setpoint control software supports many selectable functions, such as Hi or Lo activation, Latching, Hysteresis, Tracking, Register Resetting and 7 Multi-function internal Timers on all setpoints.
Control systems with large lag and lead times are not suitable for on/off control and tend to overshoot and undershoot. PID is needed to stabilize and control these systems. One of the many powerful setpoint functions provided by the Tiger 320 Operating System is single or dual PID.
Retransmission 0-10V or 4-20mA Tiger PMCs can have an optional single (0-10 V or 0/4-20 mA) or dual (0-10 V) analog output module installed. The isolated 16-bit output is fully scalable and highly accurate.
With a compliance of up to 500 at 20mA, the 4-20 mA output can be used over very long distances and still drive more than one output device, such as a PID controlled valve positioner.
The analog outputs can be reversed to output 20mA to 4/0 or 10 to 0VDC. They can be scaled across any portion of the digital range, up to full scale. The output can be programmed to swing 0 to 20mA or 0 to 10V in one digital count to drive external logic or SSRs as additional setpoints.
Under Macro Program Control, the analog outputs can be programmed to produce pulses or even sinewaves.
I/O Logic, Rear Panel or Breakout Box The Tiger Operating System has many built-in logic functions that can be used to develop sophisticated control systems. The Tiger PMC has three logic inputs/outputs available via the LOCK, HOLD, and CAPTURE pins, and three logic I/Os are available for input module use via pins D1, D2 and D3.
More complex I/O intensive applications require an opto-isolated I/O plug-in module, which supports six inputs and up PLANNING to 16 outputs. This module can connect to an external TIP
Breakout Box that is DIN Rail mountable with screw terminal blocks. There are also compatible DIN Rail mounting electromechanical relays and SSR modules.
6 Inputs & 16 Outputs or 6 Inputs & 6 Outputs
Fully Programmable
The easiest way to configure or program a Tiger PMC is with the free user-friendly Configuration or Macro Development Software. Serial I/O is provided via an optional Plug-in output carrier board, which supports RS-232 or RS-485 output modules. If serial I/O is not required by the application, the serial carrier board can be removed for reuse. The Tiger 320 Operating System supports several serial protocols, including ASCII, Modbus RTU and Print Mode (which includes a printer driver and support for direct meter to meter communications).
Also supported is DeviceNet, which requires a special dedicated carrier board, and Ethernet (TCP/IP), which requires an external converter box.
RS-232 or RS-485
Except for DeviceNet, all serial communication modes supported by the Tiger can function with either RS-232 or RS-485. The limitations of RS-232 are that only one meter at a time can be connected to the serial port of a computer, and the
distance from the computer to the meter is limited in practical terms to around 30 meters (100 feet).
Up to 32 meters can be connected on an RS-485 bus.
The differential current drive of the RS-485 bus ensures signal integrity in the most harsh environments to distances up to 1230 meters (4000 feet). However, RS-485 generally requires a special RS-485 output card to be installed in the computer or an external RS-232 to RS-485 converter has to be used.
DECISION
Modbus (RTU)
Modbus is widely used in industry. It has a large base, and most SCADA and HMI software packages support it. See also Modbus Wrapped in Ethernet (Modbus/TCP) below.
There are 100s of HMI Touch Panel Screens that are compatible with the Tiger 320 Modbus interface.
ASCII
The meter configuration utility program and the development software use the ASCII protocol. The ASCII protocol allows you to write your own driver for your own application via the development software and should provide the quickest development time.
Print Mode
This is an ASCII based printer driver output that enables the serial port to be directly connected to any serial printer with Epson compatibility. Printer output can be configured to occur from a setpoint or on demand, and can be date or time stamped.
The print mode can also be used for computer data logging applications. The meter can be connected directly to a computer, set up in Microsoft Hyperterminal mode, with the meter programmed to output directly into a Microsoft Excel spreadsheet format. (Also see Data Logging).
Print Mode for Meter to Meter Communication Two or more Tiger PMCs can be connected together allowing data to be transferred from the master meter (in print mode) to the slave meter (in ASCII mode). This enables the meters to share input data and control output functions.
Master Mode
This mode is for use with macro programming to expand the meter to meter communication capability to multiples of Tiger PMCs. This is useful for building an entire system of Tiger PMCs, sharing information and control output resources.
DECISION
Ethernet
Ethernet has become a popular automation and control protocol. We supply an ethernet output option and several external ethernet converters that are compatible with the serial outputs of Tiger PMCs.
Ethernet ASCII Wrap - The ethernet output carrier board option wraps the ASCII output into the Ethernet protocol, and provides a T-base 10/100 Ethernet output socket. This allows the Configuration Utility Program or the Macro Development Software to run over a standard Ethernet network. This enables the Tiger meter to be configured or macro programmed from anywhere in the world via the web.
Up to 32 Tiger PMCs can be connected by RS-485 to a single Ethernet Converter, which will support up to 32 separate IP addresses.
Ethernet Modbus Wrap - This converter accepts the Tiger PMCs modbus protocol and outputs Modbus/TCP through an Ethernet T-base 10 port. This has become a standard for Ethernet on the factory floor. Many SCADA and HMI software packages connect directly to Modbus/TCP.
DeviceNet
DeviceNet was originally developed by Allen Bradley to connect sensors from the factory floor to PLCs. It is a deterministic real-time system, typically used to connect to networks using Allen Bradley PLCs. An optional carrier board is required for DeviceNet which replaces the standard serial output with a dedicated DeviceNet output connector.
The Tiger 320 Operating System has built-in, sophisticated data logging software. Data logging can be triggered from the PROGRAM button, digital inputs, time or alarm functions. Up to 1MB of optional extra on-board memory provides a powerful, multichannel data capture and acquisition system.
Tiger PMCs can be configured to log in an endless loop, overwriting the oldest data first and utilizing the maximum amount of memory available. Similar to the Black Box on an aircraft, the data can be downloaded for analysis after a problem event occurs.
Data logging can be combined with an Ethernet converter to provide an individual Web Page with data that can be accessed by a browser over the internet.
Real-time Clock
The Tiger meter has an optional real-time clock with a 15 year lithium battery backup, ensuring that time information is not lost in the event of a power failure. It can be configured in 12 or 24-hour modes for printing and data logging applications.
Other applications of the real-time clock include activating a setpoint or control action at fixed times of the hour, day, week, month or year.
Flash Card Memory Module For long term data logging, a Flash Card Memory Module that plugs in to the carrier board output socket is available. Flash Cards are available from
4 to 128 meg. They can be removed and read by a standard card reader, or the data can be downloaded through the serial port or over the internet with an Ethernet converter. The module also has an SSR setpoint output to trigger an external event.
With a serial output module installed, Tiger 320 PMCs are most easily configured using the Tiger 320 Configuration Utility, which can be downloaded free from the web and run on any Windows-based PC. The utility also enables the user to access some special capabilities of the Tiger 320 which cannot be programmed manually by the front panel buttons.
The Configuration Utility requires that an RS-232 interface board be installed in a Tiger 320 for programming.
However, if the final application does not require a serial output, the RS-232 board can be easily removed, after programming is completed, and kept for future use.
When a Tiger 320 is to be used in a custom application, the utility enables all or any of the front panel programming functions to be disabled (code blanking).
Customized descriptive text can also be entered to appear with any setpoint action or event.
Different configurations can be stored in a PC for fast downloading into a meter by the user. Custom configurations can also be issued a serial number and pre-
loaded at the factory.
Custom Macro Programming
This powerful, easy to use development system enables programs to be written in BASIC, utilizing any combination of the hundreds of functions and thousands of registers embedded in the Tiger 320 Operating System. When your Basic program is compiled into the Tiger 320 Macro-language it is error checked and optimized. There are also numerous offthe-shelf application specific programs available. Many only need the blanks to be filled in to use them and do not require any knowledge of BASIC programming.
Macro in the
writing stage
Macros are useful when implementing any specialized control system that cannot be achieved by the standard configuration capability of the Tiger 320 Operating System. Using the development software, functions can be altered or added in a standard meter to perform the required job. This may typically include logic sequencing functions and mathematical functions.
Developing a Macro is much easier and quicker than programming a PLC, because the basic code required to customize the Tiger meter is considerably less than the ladder logic programming required for PLCs. This is due to the hundreds of functions built into the Tiger meter that can be manipulated or invoked by a macro, to fulfill the requirements of almost any application.
S c r o l l i n g annunciator
m e s s a g e s can be programmed
to appear with any setpoint activation, selected events or logic inputs. Easy to read, plain text prompts can be programmed to replace the manual programming codes and provide a userfriendly interface for any custom application.
RAW DATA ANALOG, DIGITAL AND LOGIC I/O
The Easiest and Fastest Way to Configure the Tiger 320 is to Use a PC with the Free Downloadable Configuration Utility Program The diagrams and instructions provided in this data sheet / user manual are intended to enable the Tiger meter to be configured and programmed manually using the front panel buttons. A system of Programming Codes is required to facilitate this type of manual programming and these are explained in detail with diagrams and examples.
However, when the Tiger meter is configured and programmed via the optional RS-232 serial port and a PC using the Configuration Utility, the system of Programming Codes is bypassed. The Configuration Utility enables all the programming options to be clearly identified by their functions for direct on-screen selection. The Configuration Utility requires that an RS-232 interface board be installed in a Tiger 320 for programming. However, if the final application does not require a serial output, the RS-232 board can be easily removed, after programming is completed, and kept for future use.
The Configuration Utility Program (which may be freely downloaded from the web) is designed to simplify and speed up the configuration and programming of any Tiger 320. Pull down menus facilitate the selection of different options and the assignment of values. A Help explanation is provided just by holding the cursor over any function box.
The configuration utility enables the user to access some special capabilities of the Tiger 320 which cannot be selected manually by the front panel buttons.
Easy Installation of Linearization Tables
The configuration utility facilitates the storage and downloading of complex linearization tables. Tables can be created in any mathematical or spreadsheet program, and copied into the utility. Linearization tables can be created to precisely match a particular sensor so that they can be installed and downloaded as part of an annual calibration procedure.
Code Blanking
When a custom configuration is created for any specialized application, the Tiger 320 can be programmed to blank out and disable all or any manual programming codes that you do not wish the user to be able to view or access by de-selecting them in the appropriate check box.
Display Text Editing
The meter can be programmed to display customized text to appear for any setpoint or event to suit any application requirements.
Easy Setpoint Configuration
The Tiger 320 supports an incredible range of setpoint options and functions. The utility makes is quick and easy to select and download any combination you may require.
Configuration Data Copying and Loading The configuration utility program allows you to store a record of a meters configuration for later referral, or for the restoration of a desired configuration. Macros can be combined with a configuration file so they can be downloaded together and locked at the same time. When a file is locked after downloading, it cannot be copied. It can only be erased and reloaded from a master file.
Also included is the ability for the user to make notes about the configuration that can be stored as part of the file.
This powerful, easy to use Development System can be downloaded free from the web. It enables programs to be written in BASIC, which can utilize any combination of the hundreds of functions and thousands of registers embedded in the Tiger
320 Operating System.
When your BASIC program is compiled into the Tiger 320 Macro-language it is error checked and optimized. When your Macro is downloaded into a Tiger 320 and locked, it is locked forever. It cannot be read or duplicated, it can only be erased.
There is no back-door access. A Tiger 320 running your Macro will remain your exclusive proprietary product.
There is also a growing library of off-the-shelf application specific macro programs available. Many only need the blanks to be filled in to use them and this does not require any knowledge of BASIC. The source code is provided with these programs so they can easily be customized and/or integrated into any proprietary application-specific Macro.
On request, any custom Macro can be issued a serial number and pre-installed at the factory to operate on power-up.
Scrolling annunciator messages can be programmed to appear with any setpoint activation, selected events or logic inputs.
Easy to read, plain text prompts can be programmed to replace the manual programming codes and provide a user-friendly interface for any custom application.
Tiger Development System - Code Writing Screen
Register Labels
Code Writing Area
Tiger Development System screen showing Macro being written.
Double clicking on
register label in the left hand side frame
automatically inserts the function in the code window at the cursor insertion point.
Tiger Development System screen showing the Macro code being compiled successfully.
Tiger Development System screen showing the compiled Macro being downloaded into a Tiger 320 Series PMC.
32-Bit Operating System....................................................4 Analog Output / Analog Retransmission..........................21-22 Calibration of Analog Output............................................21 Dual (0-10V) Analog Output............................................21 Location of Analog Output Module..................................47 Pinout of Analog Output..................................................46 Scaling of Analog Output................................................21, 22 Select Source for Analog Output....................................21 Auto Zero Maintenance for Weighing Applications..........22 Set Parameters for CH1, CH2, CH3 & CH4....................21 Averaging - Digital Filtering................................................22 Set Parameters for CH1, CH2, CH3 & CH4....................21
Block Diagram of Software & Hardware............................9 Brightness Display..............................................................20
Calibration............................................................................21-24
Calibration Thermocouple or RTD..................................21 Manual Calibration..........................................................23
Single-Point Calibration....................................................23
Two-Point Calibration......................................................23
Case Dimensions................................................................60
Modular Construction......................................................47
Other Case Sizes............................................................3, 4 Channel 1 Settings..............................................................31-32
32 Point Linearization......................................................32 Analog Input Signal Sample Rate....................................31 Counter/Resident Timer/Clock........................................31
Measurement Task..........................................................31
Post Processing..............................................................32
Print Mode........................................................................32
Sampling Rate................................................................31
Serial Mode......................................................................32
Smart Input Module........................................................31 Channel 2 Settings..............................................................33 Channel 3 Settings..............................................................34 Channel 4 Settings..............................................................35 Channel 1 & Channel 2 Results Processing
32 Point Linearization......................................................36 Maths Functions..............................................................36
Code 1 - Display Configuration..........................................25-30 Configure Data Source Procedure..................................27 Configure Display Format Mode Procedure....................28 Configure Last Digit Text Char. Procedure......................29 Configure Setpoint Annunciators Procedure..................30 Configure Update at Sample Rate Procedure................30 Data Source - 2nd Digit [X5X]........................................25 Display Format - 2nd Digit [X6X]....................................25 Display Functions Mode..................................................25 Manual Loader Mode......................................................25 Setpoint Annunciators Mode............................................25
Text Character - 2nd Digit [X7X]......................................25 Update Display at Selected Sample Rate........................25
Code 2 - Channel 1 Measurement Task
and Sampling Rate........................................................31
Code 3 - Channel 1 Post Processing
and Serial Mode Functions..........................................32
Code 4 - Channel 2 Measurement Task
and Sampling Rate........................................................33 Code 5 - Channel 3 Functions............................................34 Code 6 - Channel 4 Functions............................................35 Code 7 - Result Processing................................................36 Code 8 - Data Logging & Print Mode................................37
Code 9 - Functions for Digital Input Pins..........................37 Code Blanking......................................................................19-20
Clock/Timer
Configuration....................................................................31, 34, 35
Optional Real-time Clock................................................4 Real-time Clock Configuration........................................31, 34, 35 Real-time Clock Date......................................................37 Time Stamp......................................................................37
Component Layout & External Devices............................47-48 Modular Construction......................................................47
Component Layout..........................................................48
Configuration and Programming from a PC....................4, 8 Configuration Utility Program
Code Blanking and Display Text Editing..........................10 Configuration Data Copying............................................10 Installation of Linearization Tables..................................10 Setpoint Configuration....................................................10
Connections
Carrier Board Output Pinouts..........................................46 Connector Pinouts..........................................................45
DeviceNet........................................................................46
External Devices..............................................................48
Ordering Information, Connectors..................................58 Rear Panel Pinout Diagram............................................45 Controls & Indicators..........................................................14-15 Annunciator LEDs............................................................14
Down Button....................................................................14
Error Message................................................................15
LED Display....................................................................14
Program Button................................................................14
Program Lockout Switch..................................................15 Scrolling Display Text Messaging....................................14 Setpoint Lockout Switch..................................................15 Seven Segment LED Displays........................................14 Up Button........................................................................14
Control Outputs..................................................................6-7
Electromechanical Relays
or Solid State Control Outputs........................................6 I/O Logic, Rear Panel or Breakout Box............................7 PID or ON/OFF Control..................................................7 Retransmission 0-10V or 4-20mA....................................7
Custom Macro Programming
Macro Compiling and Loading........................................11 Data Logging........................................................................4, 8, 37 Downloading Logged Data from Meter............................37 Flash Card Memory Module............................................8 Printing Logged Data......................................................37 Real-time Clock................................................................8, 37
Development Software
When to Use Macros......................................................8 DeviceNet..............................................................................8, 46
Digital Input Pins................................................................37 Display Brightness Setting................................................20 Display Functions................................................................25-30
Data Source....................................................................27
Display Format and Decimals..........................................28 Display Rounding............................................................28
Last Digit Text Character..................................................29 Other Display Formats....................................................4 Setpoint Annunciator Mode..............................................30
Update at Sample Rate..................................................30
Display Options
LED or LCD Displays......................................................6 Numeric or Alphanumeric Displays..................................6 Push Button or Membrane Touch Pads..........................6 Remote Display................................................................6
Single or Multiple Displays..............................................6
Faceplates
Custom Faceplates..........................................................59
Optional Caption Sheets..................................................59 Custom Faceplate Design Template................................59
Filtering
See Averaging Samples & Averaging Window
Front Panel Controls..........................................................4, 14-15 Front Panel Programming Codes......................................17-18 Main Programming Mode................................................17 On Demand Modes..........................................................18
Setpoint Programming Mode..........................................17 View Modes....................................................................18
Functional Diagram............................................................45
General Features................................................................1
HMI Touch Panel Graphic Displays....................................7 Hysteresis and Deviation....................................................39-40, 42 Initial Setup Procedures......................................................19-20
Code Blanking and Macro Check....................................19-20 Model and Software Code Version Check......................19 Input Signal Conditioning Modules..................................5, 49-55 Input Module Component Glossary................................55 Input Module Index..........................................................49 Input Modules..................................................................50-54
Modular Position..............................................................47
Ordering Information, Input Modules..............................56-57
Input Signals & Sensors
4-20mA or Sensor Direct................................................6 Sensor Linearization or Compensation............................6 I/Os (Opto Isolated & Logic Ports)....................................5, 48 Linearization
Channel 1 Temperature Sensors....................................31 Channel 1 User Loaded Tables........................................32 Channel 2 Temperature Sensors and User Loaded Tables..................................................33 Channel 3 Temperature Sensors and User Loaded Tables..................................................34 Channel 4 Temperature Sensors and User Loaded Tables..................................................35 Result of CH1 & CH2 User Loaded Tables......................36 Table Settings..................................................................22, 36
Literature Overview
Model Specific Data Sheets / User Manuals..................3 Other Tiger 320 Series Related Software........................3 Programming Code Sheet..............................................3 Supplements to Data Sheets / User Manuals..................3
Macros..................................................................................4, 8, 11 Macro Check....................................................................19-20
Manual Loader....................................................................25
Maths Function
Cross Channel Maths......................................................9, 36 Result Processing............................................................36
Modbus................................................................................7, 22
Model Type Check................................................................19
On Demand Functions........................................................21 Ordering Information..........................................................56-58
Panel Cutout........................................................................60
PID Control Settings............................................................39, 42 Power Supply......................................................................5, 45 Prescaling
Channel 1........................................................................31
Channel 2........................................................................33
Print Mode............................................................................7, 32 Programming Codes............................................................17-18
Programming Conventions................................................16
Programming via PC..........................................................4, 10-11 Registers
Registers That Can Be Selected....................................44 Registers That Should Not Be Selected..........................44 Resetting and Incrementing Using Setpoints..................44 Relay & Logic Output Modules..........................................46 Serial Communication........................................................5, 7-8 ASCII................................................................................7
Configuration....................................................................32
DeviceNet........................................................................8
Ethernet..........................................................................7
Master Mode....................................................................7
Modbus............................................................................7
Pinouts............................................................................46
Print Mode........................................................................7
RS-232 or RS-485..........................................................7 Setpoint Programming Mode..............................................38-43
Data Logging....................................................................39
Data Printing to PC..........................................................39 Data Printing to Serial Printer..........................................39 Display Flashing..............................................................39
Hysteresis or Deviation....................................................39-40, 42 Level 1 - Basic Mode - Prog. Procedures........................41 PID Control Settings........................................................39, 42 Real-time Clock Option....................................................39 Real Time Control Modes................................................40 Relay Energize Functions................................................39 Relay Output Modules....................................................38 Setpoint & Relay Control Settings..................................38, 42 Setpoint Activation Source..............................................39 Setpoint Activation Values................................................38
Setpoint Latching............................................................39
Setpoint Reset & Trigger..................................................39, 43 Setpoint Tracking..............................................................39
Timer Modes....................................................................39, 43
Smart Input Modules
Setting Up........................................................................31
Supplements
See Literature Overview
Table of Contents................................................................1 Timers..................................................................................5, 39
Configuration....................................................................31, 34, 35
Delay Settings..................................................................43
Modes..............................................................................40
Totalizers
Setting..............................................................................21-22
See Display with Faceplate and Bezel diagram.
Annunciator LEDs
The annunciator LEDs can be programmed to indicate the alarm status.
Setpoint 1 can be configured to indicate the rising signal trend.
Setpoint 2 can be configured to indicate the falling signal trend.
They are labeled from left to right: SP1, SP2, SP3, SP4, SP5, SP6.
See Display with Faceplate and Bezel diagram.
LED Display
The DI-60A5C has a 6-digit, 14-segment, 0.56(14.2 mm) standard red, or optional green, or super-bright red LED display. The LED displays are used to display the meter input signal readings. They also display the programming codes and settings during meter programming.
See Ordering Information for further details.
Display Text Editing with 14 Segment Full Alphanumeric Display Characters
Display text, such as setpoints, can be easily edited to suit your application, by connecting the meter to a PC running the free downloadable Configuration Utility program.
For Example:
Instead of [SP_1]
Instead of [SP_2]
could be used for TANK LOW
could be used for BRAKE OFF
Scrolling Display Text Messaging Scrolling display text messaging can be configured to run with a simple macro.
Display Text Characters
The following text characters are used with the 14-segment full alphanumeric display.
14-SEGMENT DISPLAY CHARACTERS
and
buttons.
button saves the current pro-
Program Button
While programming, pressing the gramming settings and moves to the next programming step.
You can move through the programming codes using the program button. The codes you pass are not affected, unless you stop and make changes using the Pressing the button at the same time initiates the main programming mode. To save a new configuration setting and return to the operational display, press the button once and then press the button at the same P time.
Pressing the button at the same time initiates the setpoint programming mode. To save a new configuration setting and return to the operational display, press the button once and then press the button at the same time.
See Display with Faceplate and Bezel diagram.
and
and
and
button to increase the value of the displayed parameter.
Up Button
When setting a displayed parameter during programming, press the
When in the operational display, pressing the button initiates a viewing mode that allows you to view the readings on channels 1 and 3, setpoints 1, 3, and 5, peak, and total 1. Once into the viewing routine, pressing the button moves through each displayed parameter.
See Display with Faceplate and Bezel diagram.
button to decrease the value of the displayed parameter.
Down Button
When setting a displayed parameter during programming, press the
When in the operational display, pressing the button initiates a viewing mode that allows you to view the readings on channels 2 and 4, setpoints 2, 4, and 6, valley, and total 2. Once into the viewing routine, pressing the button moves through each displayed parameter.
See Display with Faceplate and Bezel diagram.
Function Buttons
Function buttons activate pre-programmed macros on and demand. each macro is written to activate from a specific function button. When the function button is pressed, the macro carries out its designated tasks.
When the PROGRAM LOCKOUT switch is set to position 2, all programmable meter functions can be changed.
When set to the ON position, the PROGRAM LOCKOUT switch prevents any programming changes being made to the meter. If programming is attempted, the meter displays [LOC].
The ON position allows programming parameters to be viewed but not changed.
See Display PCB without Faceplate and Bezel diagram.
Setpoint Lockout Switch
When the SETPOINT LOCKOUT switch is set to position 1, the setpoints can be programmed. Once the setpoint values have been entered and the SETPOINT LOCKOUT switch set to the ON position, the setpoints can be viewed but not changed.
See Display PCB without Faceplate and Bezel diagram.
Error Message [ERROR]
Error messages usually occur during calibration procedures.
The three most likely causes of an error message are:
1) The full scale and zero signals were too similar.
Note, the high input (full scale) signal
must be at least
1000 counts greater
than the low input
(zero) signal (positive and negative
values are allowed).
2) The scaling requirement exceeded the
capability of the meter (19999 to +99999).
3) No input signal present, or incorrect connections.
The main programming mode can be entered, but only the brightness setting adjusted. After adjusting the brightness setting, pressing the
button displays [LoCK].
The LOCK pin can also be configured in Code 9 to carry out the following functions (see Meter Programming Codes on Page 17):
Reset channel 1 [XX1].
Reset channel 2 [XX2].
Reset channel 3 [XX3].
Reset channel 4 [XX4].
Reset tare [XX5].
Reset total 1 [XX6].
Unlatch (de-energize) all setpoints [XX7].
Hold Pin
Configure Code 9 to [X0X]. When the HOLD pin (pin 9) is connected to the COMMON pin (11) the displayed reading is frozen.
However, A/D conversions and all control functions continue and as soon as pin 9 is disconnected from pin 11 by the switch, the updated reading is instantly displayed.
The HOLD pin can also be configured in Code 9 to carry out the following functions (see Meter Programming Codes on Page 17):
Reset tare [X5X].
Set tare [X6X].
Unlatch (de-energize) all setpoints [X7X].
Test Pin
Configure Code 9 to [0XX]. When the TEST pin (pin 10) is connected briefly to the COMMON pin (pin 11) all segments of the display and setpoint annunciators light up. Six eights and six decimal points (8.8.8.8.8.8.) are displayed for a short period. The microprocessor is also reset during this time, losing all RAM settings such as peak and valley, and any digital input pin settings set up in Code 9.
The TEST pin can also be configured in Code 9 to carry out the following (see Meter Programming Codes on Page 17):
Reset counter channel 1 and total 2 at power-up [1XX].
Reset counters, CH1, CH2, CH3, CH4,
total 1, and total 2 at
Reset channel 1 [X1X].
Reset total 1 and total 2 [X2X].
Reset total 2 [X3X].
Reset peak and valley [X4X].
power-up [2XX].
Lock Pin
By configuring Code 9 to [XX0], connecting the LOCK pin (pin 8 on the main PCB) to the COMMON pin (pin 11 on the main PCB), locks out the main and setpoint programming modes.
All meter programming
codes and setpoints can be viewed but not changed.
Reset total 1 and total 2 at power-up [3XX].
Capture Pin
When the CAPTURE pin (pin 12) is connected to the COMMON pin (pin 11), the CAPTURE pin can be programmed for setpoint/relay activation or macro control applications in the setpoint control settings mode of the setpoint programming mode [SPCX] [X2X].
Common Pin
To activate the LOCK, HOLD, TEST and CAPTURE pins from the rear of the meter, the respective pins have to be connected to the COMMON pin (pin 11).
The meter uses a set of intuitive software codes to allow maximum user flexibility while maintaining an easy programming process.
To configure the meters programming codes, the
meter uses the three righthand side display digits.
These are known as the 1st, 2nd, and 3rd digits and can be seen in the diagram opposite. To explain software programming procedures, diagrams are used to visually describe the programming steps.
Operational Display
First
Digit
Second
Digit
Third
Digit
The following conventions are used throughout the range of Tiger
320 Series document diagrams to represent the buttons and indicators on the meter, and the actions involved in programming the meter:
Symbol
Explanation
The top display showing 99999 represents the OPERATIONAL DISPLAY. After the meter has been powered up, the display settles and indicates the calibrated input signal.
This is known as the operational mode and is generally referred to as the operational display throughout the documentation.
All programming modes are entered from this level.
This symbol represents the PROGRAM button. In a procedure, pressing the program button is always indicated by a left hand. A number indicates how many times it must be pressed and released, or for how long it must be pressed before releasing.
Operational Display
This symbol represents the UP button.
Shown in a diagram, pressing the UP button is always indicated by a right hand.
This symbol represents the DOWN button.
Shown in a diagram, pressing the DOWN button is always indicated by a right hand.
Where two right hands are shown on the same diagram with the word OR between them, this indicates that both the buttons can be used to adjust the display: UP for increase, DOWN for decrease.
and
Programming procedures are graphic based with little descriptive text.
Each procedure shows a number of meter panel displays running in procedural steps from the top to the bottom of the page.
If need be, the procedure may run into two columns with the left column running down the page and continuing at the top of the right-hand column. Each action performed by the user is shown as a numbered step.
Each procedural step shows the meter display as it looks before an action is performed. The hand or hands in the procedural step indicate the action to be performed and also how many times, or for how long, the button is to be pressed.
For example, the diagram below shows the meter in the operabutton and a right tional display. With a left hand pressing the
hand pressing the button, the user is entering the main programming mode. This is indicated by the next diagram displaying [bri] and [5].This is the display brightness mode and is the first submenu of the main programming mode.
Operational Display
Where a left and right hand are shown on separate buttons on the same diagram, this indicates that the buttons must be pressed at the same time.
The only exception to this rule is when carrying out the Model and Software Code Version Check.
When two displays are shown together as black on grey, this indicates that the display is toggling (flashing) between the name of the function and the value or configuration setting.
Where a number is not definable, the default setting [000] is shown.
If an X appears in the description of a 3digit programming code or in a configuration procedure, this means that any number displayed in that digit is not relevant to the function being explained, or more than one choice can be made.
[Span]
[10000]
Text or numbers shown between square brackets in a description or procedure indicate the programming code name of the function or the value displayed on the meter display.
The meters programming codes are divided into two modes:
the main programming mode, and the setpoint programming mode (See diagram below).
Each mode is accessible from the operational display.
Main Programming Mode
The main programming mode provides access to program all meter functions, except setpoints.
To enter or exit the Main Programming Mode, press
at the same time P
and
Main Programming Mode
Display Brightness
[bri]
[CAL]
Calibration Modes for Input and Output
[Cod_1]
Code 1 Display Configuration
Programming Tip
The easiest and fastest way to configure the Tiger 320 is to use a PC with the free downloadable configuration utility program. (see page 10)
Setpoint Programming Mode
The setpoint programming mode provides access to program all setpoint and relay functions.
To enter or exit Programming Mode, press
at the same time
the Setpoint
and
Setpoint Programming Mode
Setpoint Activation Values Mode
Programming Tip
Save SP Settings & Exit To save a new setpoint configuration setting and
return to the operational display at any point,
Enter these menus to adjust SP activation values
[SP_1]
Setpoint 1
[SP_2]
Setpoint 2
press
once.
the
button
[SP_3]
Setpoint 3
[Cod_2]
Code 2 CH1 Measurement Task & Sampling Rate
Then press the
and
button at the same
time to exit.
[SP_4]
Setpoint 4
[Cod_3]
Code 3 CH1 Post Processing & Serial Mode Functions
[Cod_4]
Code 4 CH2 Measurement Task & Sampling Rate
[Cod_5]
Code 5 CH3 Functions
[Cod_6]
Code 6 CH4 Functions
[Cod_7]
Code 7 Result Processing
Programming Tip
[Cod_8]
Code 8 Data Logging & Print Mode
[Cod_9]
Code 9 Functions for Digital Input Pins
[Cod10]
Code 10 Bargraph Setup
[SP_5]
Setpoint 5
[SP_6]
Setpoint 6
Setpoint & Relay Control Settings Mode
Enter these menus to configure SP control values Setpoint 1
[SPC_1]
[SPC_2]
Setpoint 2
[SPC_3]
Setpoint 3
[SPC_4]
Setpoint 4
[SPC_5]
Setpoint 5
[SPC_6]
Setpoint 6
While in the operational display, pressing the you to view but not change the following parameters:
button allows
Channel 1.
Channel 3.
Setpoint 1.
Setpoint 3.
Setpoint 5.
Peak (of CH1).
Total 1 (total of CH1).
While in the operational display, pressing the you to view but not change the following parameters:
button allows
Channel 2.
Channel 4.
Setpoint 2.
Setpoint 4.
Setpoint 6.
Valley (of CH1).
Total 2 (total of CH2).
To view, press the
button:
To view, press
the
button:
View Mode
Ch1
Ch3
SP_1
SP_3
SP_5
PEAK
tot_1
View Mode
Ch2
Ch4
SP_2
SP_4
SP_6
VALEY
tot_2
On Demand Modes
The meter can be programmed to activate the following functions on demand by pressing the
button for 4 seconds:
Tare.
Single-point calibration.
Two-point calibration.
Primary input compensation.
Manual loader (manual offset).
Print.
The on demand function is selected in the calibration mode.
After configuring an on the function demand
Calibration On Demand
Mode, press the button for
4 seconds to activate one of following selected on the demand modes.
On Demand Modes
Tare
Single-point calibration
Two-point calibration
Primary input compensation
Manual loader (manual offset)
For a full breakdown of all programming codes, see the Tiger 320 Series Programming Code Sheet (NZ101). See page 3 for more information.
Before configuring the meter, carry out the following meter configuration checks:
Model and software code version check.
Code blanking and macro check.
After powering-up the meter, check the model and software code version number and note this in your user manual.
The meter model and software code version number can be checked at any time while in the operational display using the following procedure.
T HERE STSTARART HERE
Operational Display
MODEL &
SOFTWARE CODE
VERSION CHECK
Example
Operational Display
Programming Tip
The Model and Software Code Version checking procedure can be performed at any time without interfering with other configuration settings.
Code Blanking and Macro Check Tiger 320 Series meters have the ability to hide (blank out) all or some programming codes, making them tamper-proof. This can only be done using the Meter Configuration program.
With code blanking turned ON, all main and setpoint codes that have been blanked out during factory programming are hidden, preventing them from being reprogrammed. Any codes that have not been blanked out are still visible and can be reprogrammed.
Turning code blanking OFF means all meter programming codes are visible when you enter the programming modes and can be reprogrammed.
A macro is a set of commands that run automatically when the meter is powered up. We have a growing library of macros to suit a wide range of standard customer applications.
Macros can be installed in the meter at the factory during initial programming or by the customer at some later date. Macros are written and compiled using the BASIC Compiler program, and loaded into the meter using either the BASIC Compiler program or the Meter Configuration program.
Turning the macro OFF means that the meter will not perform the automatic commands pre-programmed to run with the macro.
Unless requested to blank out all or some programming codes and/or run a macro, we will program the meter in the code blanking OFF and macro OFF (default) setting.
To turn the code blanking and macro settings from ON to OFF:
T HERE STSTARART HERE
CODE BLANKING &
MACRO CHECK
PROCEDURE
Step 1
Press and hold
the and
buttons
Operational Display
Example
Step 5
Press the Prog. button.
Example
Step 7
Press the Prog. button.
Operational Display
Programming Tip
Code Blanking and Macro ON/OFF settings revert to the meters original configuration settings when the meter is powered off and on.
Once you have read the user manual and related supplements, and installed and powered-up the meter, configure the display to suit its designated application.
Display Brightness Mode
The display brightness mode is accessed when entering the main programming mode. It allows you to adjust the brightness of the display LEDs and setpoint annunciators without interfering with other configuration settings. It is always available, even with the PROGRAM LOCK switch set to ON, or the external LOCK pin connected to the COMMON pin, locking out the programming modes.
The display brightness can be set between 0 and 7, with 0 being dull and 7 being bright. The default setting is 5.
Example Procedure:
Configure the display brightness setting to 7 (bright).
T HERE STSTARART HERE
DISPLAY
BRIGHTNESS
MODE
Operational Display
Example
Operational Display
Programming Tip
The Display Brightness setting procedure can be performed at any time without interfering with other configuration settings by entering the main programming mode.
The Tiger 320 Series meter has an extremely powerful set of input and output calibration modes. See diagram below.
In this mode the meter can be programmed to activate one of the following on demand functions by pressing the button while in the operational display:
On Demand TARE.
On Demand Single-point Calibration (requires single input source).
On Demand Two-point Calibration (requires dual input source).
On Demand Primary Input Compensation Mode.
On Demand Manual Loader Mode.
The following calibration modes are available:
Manual Calibration (requires NO input source).
Two-point Calibration (requires dual input source).
This is the calibration mode generally used to calibrate the meter for most applications. An example procedure has been included.
Calibrate Thermocouple (requires K type thermocouple
input source).
Calibrate RTD (requires RTD 385 input source).
Calibrate Smart Input Module (not available on all input
modules).
Calibrate Analog Output (requires multimeter connected to pins
16 and 17).
Related Calibration Functions
The following functions are also configured in the calibration mode. See Advanced Calibration and On Demand Mode Supplement (NZ203) for further calibration details. (See page 3 for more information).
Serial Communications Properties
Selecting [CAL][20X] enters the Serial Communications Properties Mode.
This mode allows you to configure the serial communications output module baud rate, parity, time delay, and address settings.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
Also see the Serial Communications Module Supplement
(NZ202) for further details on the serial communications module. (See page 3 for more information).
Set Auto Zero Maintenance Selecting [CAL][21X] enters the Set Auto Zero Maintenance Mode.
This mode allows you to configure auto zero maintenance settings for weighing applications applied to the channel selected in the 3rd digit.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
Set Averaging Samples & Averaging Window Selecting [CAL][22X] enters the Set Averaging Samples and Averaging Windows Mode.
This mode allows you to configure the number of input signal samples to average over, and the size of the averaging window in display counts applied to the channel selected in the 3rd digit.
Selecting [CAL][22X] enters the Set Averaging Samples and Averaging Windows Mode. When in this mode, the [AV_S] menu allows you to select the number of input signal samples to average over. After setting the number of samples, moving to the [AV_W] menu allows you to configure the size of the averaging window in displayed counts.
The meter averages the input samples over the selected number of input samples (selected in the [AV_S] menu). This carries on in a continual process provided the input signal stays within the averaging window (set in the [AV_W] menu). If the sample moves out of the averaging window, the meter responds quickly to the change by displaying the non-averaged signal value.
When the signal stabilizes, a new averaging window is established and averaging resumes.
You can program the number of samples you want to average the input signal over from 1 to 255 samples. The averaging window can be set to between 1 and 65535 counts.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
See Input Signal Sampling Showing Averaging Window diagram opposite.
Example Procedure
The example procedure on Page 24 shows how to configure channel 1 (CH1) with an averaging sample rate of 10 counts and an averaging window of 1000 counts.
Totalizer Settings
Selecting [CAL][23X] enters the Totalizer Settings Mode.
This mode allows you to configure the settings for the totalizer selected in the 3rd digit. An input value of 10000 counts is applied to a selectable time period to produce the required total value.
The cutoff is a programmable limit below which the input is not totalized.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
Also see the Totalizing and Batching Supplement (NZ208) for further details on K factor and totalizer cutoff parameters. (See page
3 for more information).
Setup 32-point Linearization Tables Selecting [CAL][24X] enters the Setup 32-point Linearization Tables Mode.
This mode allows you to set up the linearization table or tables using the manual or auto setup modes. The table or tables can then be selected to linearize the signals on channels 1 to 4.
See Linearization Table Notes on Page 36 for a description of memory related issues with linearization.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
Also see the Linearizing Supplement (NZ207) for further details on linearization table setup and use. (See page 3 for more information).
Scale Analog Output
Selecting [CAL][25X] enters the Scale Analog Output Mode.
This mode allows you to calibrate and scale the analog output signal. Before calibrating the analog output in the calibration mode, the data source for the analog output must be configured in Code 1.
See the calibration modes diagram on Page 21 showing a breakdown of 1st, 2nd, and 3rd digits.
Also see the Analog Output Module Supplement (NZ200) for further details on the analog output module. (See page 3 for more information).
Also see Configure Data Source Procedure on Page 27 for an example of setting the analog output data source.
Calibration Mode Procedures Supplement The Advanced Calibration and On Demand Mode Procedures Supplement (NZ203) describes in detail all Tiger 320 Series meter related calibration procedures configured in the calibration mode.
Two-point Calibration
Two-point calibration is the most commonly used method of calibrating Tiger 320 Series meters when a low and high input source is available.
Example Calibration Procedure
Calibrate channel 1 (CH1) using the two-point calibration method. Set the calibration mode display to [111].
The low input source is applied to the meter when setting the zero value.
The high input source is applied to the meter when setting the span value.
T HERE STSTARART HERE
TWO-POINT
CALIBRATION
From Step 5
Example
Step 11
Example
To Step 7
Input Signal Filtering and Averaging Input signal filtering and averaging is configured in the calibration mode. Programmable averaging allows you to program the number of samples you want to average the input signal over (from 1 to 255 samples).
A programmable averaging window provides a quick response time to large input signal changes. The averaging window can be set to between 1 and 65535 counts.
Example Procedure:
Select an averaging sampling rate of 10 samples and an averaging window of 1000 counts for Channel 1 by setting [CAL] to [221].
See Advanced Calibration & On Demand Mode Supplement (NZ203) for further calibration procedures. (See page 3 for more information).
T HERE STSTARART HERE
INPUT SIGNAL
FILTERING &
AVERAGING
Step 1
Enter
Brightness Mode
Operational Display
Step 2
Pass Brightness
Mode and enter
Calibration Mode
0 Result
1 Channel 1
2 Channel 2
3 Channel 3
4 Channel 4
From Step 5
Step 7
Select averaging
window between 1
and 65535 counts
Example
Step 8
Save averaging
window settings
Step 9
Select [000] to
leave the
Calibration Mode
Step 10
Save settings
Step 5
Select averaging sampling
rate from 1 to 255 samples
Step 6
Save averaging
sampling rate setting
Example
CODE 1 Display Configuration Modes All meter display modes, except the display brightness mode, are configured in Code 1 (See diagram below). See Code 1 diagram on Page 26 for a breakdown of 1st, 2nd, and 3rd digits settings.
Setpoint Annunciators Mode
The setpoint annunciators mode is configured by changing the first digit in Code 1. The setpoint annunciators can be configured to operate as follows:
On when the setpoint activates.
All annunciators are permanently on and each one only goes off
when its setpoint activates.
All annunciators are always off (See Note 1 on Code 1 diagram
on Page 26).
Setpoint 1 annunciator comes on indicating a rising signal.
Setpoint 2 annunciator comes on indicating a falling signal.
The example procedure on Page 30 shows how to select the setpoint annunciators to come ON when the setpoints are OFF (not active).
Update Display at Selected Sample Rate The meters default display update rate is 0.5 seconds and is set in the 2nd digit of Code 1 as [X0X].
The display can be configured to update at the analog sample rate selected in Code 2.
The example procedure on Page 30 shows how to configure the display to update at 50 samples per second by setting Code 1 to [X2X].
For these settings to take effect, the analog sample rate must be set at [2XX] in Code 2.
See Code 2 Channel 1 Measurement Task and Sampling Rate on Page 31 for an example.
Manual Loader Mode
The meter can be configured to function exclusively as a manual loader by setting Code 1 to [X1X].
See Analog Output Module Supplement (NZ200) for full details on manual loader mode functions.
Display Functions Mode
The display functions mode is configured by changing the 2nd and 3rd digits in Code 1:
Selecting [X5X] enters the Data Source sub-menu.
Selecting [X6X] enters the Display Format sub-menu.
Selecting [X7X] enters the Last Digit Text Character sub-
menu.
Data Source 2nd Digit [X5X] The data source for the primary display is configured by selecting
5 in the 2nd digit and 0 in the 3rd digit.
Note:
[XX1] Second Display is the bargraph display on models DI-50B51, FI-B101D50, and GI-50B101. The [XX1] Second Display and [XX2] Third Display only apply to DI-503 meters with three displays.
The 2nd digit in Code 1 can also be used to configure the data source for the remaining functions in the 3rd digit:
[X53] = Peak and Valley.
[X54] = Analog Output 1.
[X55] = Analog Output 2.
[X56] = Totalizer 1.
[X57] = Totalizer 2.
Selecting 5 in the 2nd digit enters a sub-menu and allows you to select the data from one of a number of meter registers as the data source for the displays or functions selected in the third digit.
The example procedure on Page 27 shows how to select the data source for the primary display. The three digits are set to [X50].
Display Format 2nd Digit [X6X] Selecting 6 in the 2nd digit enters the Display Format sub-menu where the following display format settings can all be configured:
Last digit rounding.
Display units (Decimal, octal, or optional 12 or 24-hour clock).
Decimal point placement.
The example procedure on Page 28 shows how to configure the three display format modes for the 3rd digit selection.
Text Character 2nd Digit [X7X] Selecting 7 in the 2nd digit allows you to select one of 54 characters and apply it to the last digit when the meter is in the operational display.
For example, if the meter was measuring a temperature, the display could be configured to display the reading with a C or an F in the last digit for C or F.
The example procedure on Page 29 shows how to configure the last digit text character as C for centigrade (C) for the 3rd digit selection.
Note:
After setting any or all the above three modes [X5X], [X6X], [X7X], the Code 1 display must set back to [X0X] to leave Code 1 and carry on programming.
Example Procedure:
The following example procedure describes how to select the source of the data to be displayed for the third digit selection.
Configure the Primary Display with the display [diSP] as the data source by setting Code 1 to [X50]. See diagram at the bottom of the page for data source selection options.
T HERE STSTARART HERE
CONFIGURE
DATA SOURCE
From Step 5
Step 6
Programming Tip
Step 7
Select [000] to leave Code 1
Programming Tip
Step 8
Step 4
Step 9
Step 5
Example
The following example procedure describes how to configure the display format mode for the 3rd digit selection and covers:
Last Digit Rounding.
Display Units.
Decimal Point Placement.
Example Procedure:
Configure the display format mode for channel
1 with rounding by 2s, decimal display units, and the decimal point placed between display digits 4 and 5 by setting Code 1 to [X61] to enter the Display Format Mode.
T HERE STSTARART HERE
CONFIGURE
DISPLAY FORMAT
Step 4
Step 9
Step 5
From Step 5
Example
Step 6
Step 7
Step 8
The following example procedure describes how to select the last digit text character.
Example Procedure:
Configure Channel 1 with C as its last digit text character (for C) by setting Code 1 to [X71] to enter the Select Last Digit Text Character. See diagram opposite.
T HERE STSTARART HERE
CONFIGURE
LAST DIGIT
TEXT CHARACTER
From Step 6
Step 4
Step 5
Example
To Step 7
Step 7
Step 8
Step 9
The following example procedure describes how to configure setpoint annunciators.
The following example procedure describes how to configure the display to update at the sample rate selected in Code 2.
Example Procedure:
Example Procedure:
Configure the setpoint annunciators to come ON when the setpoints are OFF (not active) by setting Code 1 to [1XX].
Update the display at the sample rate selected in Code 2 by setting Code 1 to [X2X].
T HERE STSTARART HERE CONFIGURE
SETPOINT
ANNUNCIATORS
Step 1
T HERE STSTARART HERE
CONFIGURE
UPDATE AT
SAMPLE RATE
Step 1
Step 2
Step 3
Step 2
Step 3
Step 4
Example
Step 4
Example
Step 5
Step 5
Programming Tip
The Configuring Setpoint Annunciators and the Update at Sample Rate procedures can be combined so that Code 1 could be set to [12X] (for the above examples) in a single procedure.
The Tiger 320 Series DI-50A5C meter can be configured to measure almost any input signal. The measurement task and sampling rate for Channel 1 (CH1) is configured in the three digits of Code 2.
The diagram below lists the available configuration selections in Code 2.
Example Procedure:
Configure CH1 for a voltage input with 10 samples/second (60 Hz rejection) sampling rate and output rate of 0.1 seconds by setting Code 2 to [000].
T HERE STSTARART HERE
CONFIGURE CH1
MEASUREMENT
TASK & SAMPLING
RATE
Step 1
Enter
Brightness Mode
Operational Display
Step 2
Pass Brightness Mode, Calibration Mode, Code 1, and enter Code 2
Step 3
Set Code 2 to [000]:
1st Digit = 0 Selects 10
Step 4
Save setting and
enter Code 3
Example
Post processing functions refer to functions that occur to the input after it has been configured and scaled.
Example Procedure:
Configure the meter to apply square root to the CH1 signal by setting Code 3 to [100].
Post processing for Channel
1 (CH1) is configured in the first digit of Code 3. The diagram below lists the available post processing configuration
selections in Code 3 (1st digit only).
T HERE STSTARART HERE
CONFIGURE CH1
POST PROCESSING
FUNCTIONS
Step 1
Enter
Brightness Mode
Step 2
Pass Brightness Mode, Calibration Mode, Codes 1 and 2, and enter Code 3
Operational Display
From Step 3
Step 4
Save Post
Processing setting
Programming tip
For full details on the Serial Mode, see Serial Communications Output Module supplement.
Print Mode Data Printing Direct to Serial Printer Print mode data logging is a simple method of capturing data using the meters print mode. The data can be printed directly to a serial printer from the meter.
The print mode uses the meters serial communications port to connect to a remote serial printer. The data can be printed with or without a Day: Month: Year or Hours: Minutes: Seconds time stamp.
Print Mode Data Printing Direct to PC The print mode can also be used to print data to a PC where it is logged in a Windows Terminal program.
The print mode uses the meters serial communications port to connect to the PC. The data can be logged with or without a Day: Month: Year or Hours: Minutes: Seconds time stamp.
Time stamp settings are configured in Code 8.
Time stamp settings are configured in Code 8.
Code 4 is a single code that combines all the configuration and post processing functions available for Channel 2.
When a dual input signal conditioner is installed, the second input signal is processed and displayed on CH2.
Measurement task and 32-point linearization for CH2 is configured in the 1st and 2nd digits of Code 4. The diagram opposite lists the available configuration selections in Code 4.
Example Procedure:
Configure CH2 for a direct voltage input with no linearization by setting Code 4 to [010].
See I-Series Input Modules Guide (Z87) for procedures to set up a dual input module.
CONFIGURE CH2
MEASUREMENT
TASK
Step 1
Enter
Brightness Mode
Step 2
Pass Brightness Mode, Calibration Mode, and
Codes 1 to 3, and enter Code 4
Step 4
Save CH 2
Measurement Task
setting
T HERE STSTARART HERE
Operational Display
From Step 3
Code 5 is a single code that combines all the configuration and post processing functions available for Channel 3.
When a triple input signal conditioner is installed, the 3rd input signal is processed and displayed on CH3.
Post processing and measurement task functions for CH3 are configured in the 1st, 2nd, and 3rd digits of Code 5. The diagram opposite the
available configuration selections in Code 5.
lists
Example Procedure:
Configure CH3 to display the square root of a voltage input by setting Code 5 to [11X].
See I-Series Input Modules Guide (Z87) for procedures to set up a triple input module.
T HERE STSTARART HERE
CONFIGURE
CH3 FUNCTIONS
From Step 4
Step 5
Step 4
Save CH3 setting
Code 6 is a single code that combines all the configuration and post processing functions available for Channel 4.
When a quad input signal conditioner is installed, the 4th input signal is processed and displayed on CH4.
Post processing and measurement task functions for CH4 are configured in the 1st, 2nd, and 3rd digits of Code 6. The diagram opposite lists the available configuration selections in Code 6.
Example Procedure:
Configure CH4 as direct display of voltage input by setting Code 6 to [01X].
See I-Series Input Modules Guide (Z87) for procedures to set up a quad input module.
T HERE STSTARART HERE
CONFIGURE
CH4 FUNCTIONS
From Step 4
Step 3
Step 5
Step 4
Save CH4 setting
The 3rd digit of Code 7 performs various math functions between channel 1 and channel
2 and stores this data in the result register.
The data in the result register can then be further processed by the selections made in the 1st and 2nd digits.
Example Procedure:
Configure Code 7 to add the input of CH1 and CH2 and directly display the result by setting Code 7 to [003].
T HERE STSTARART HERE
CONFIGURE
RESULT
PROCESSING
Step 1
Enter
Brightness Mode
Operational Display
See I-Series Input Modules Guide (Z87) for procedures to set up a dual, triple, or quad input module.
Linearization Table Notes
Step 2
Pass Brightness Mode, Calibration Mode, and
Codes 1 to 6 and enter Code 7
From Step 4
Step 4
Save CH1 & CH 2 Result Processing setting
Up to 4000 samples can be logged within the meter in the cyclic or linear FIFO mode and saved for later downloading to a PC, using a terminal emulation program, or printing directly to a serial printer.
Data logging can be triggered (activated) from a setpoint, the program button, or from an external switch. See the 3rd digit in the diagram below.
Data from up to four selectable registers can be logged with one of the following printer or spreadsheet style time and date stamps. All time and date stamps are generated from an optional real-time clock (see the 2nd digit in the diagram below):
No time stamp.
Month - Day - Year. Hours:Minutes:Seconds.
Day - Month - Year. Hours:Minutes:Seconds.
Hours:Minutes:Seconds.
Printer style time and date stamps have a carriage return and line feed. Spreadsheet style time and date stamps are continuous on a single line.
See Serial Communications Module Supplement (NZ202) for full details on the Data Logging and Print Mode Options.
The TEST, HOLD, and LOCK pins are located at the rear of the meter to accommodate external switched digital inputs. When switched to the COMMON pin, they can be programmed in Code 9 to perform remote resetting functions to add to the functionality of the meter.
Note:
CAPTURE, HOLD, and LOCK pins can be a setpoint activation source. See Setpoint Programming mode.
All setpoint activation and control settings are selected and configured using the front panel buttons in the setpoint programming mode. Or, software configured via the meter configuration utility program if the meter is connected to a PC through the serial port. The meter has six software driven setpoints, independently configured to operate within the total span range of the meter and the selected input module.
Five standard relay output module options provide a selection of 20 relay configuration options for DI-50 meters.
Three electromechanical relay output modules support a combination of 5 A Form A and 10 A Form C relays providing 12 configuration options. A solid state relay (SSR) output module supports 400 V, 210 mA DC SSRs and another SSR output module supports 400 V, 140 mA AC / DC SSRs providing a further eight configuration options.
A 22 opto-isolated I/O plug-in module can support six inputs and up to 16 outputs. The standard plug-in module has six inputs and six outputs that can be extended to 16 outputs with a 10 output add-on board.
320 Series Relay Output Module Options
Max Four
140 mA
(AC/DC)
Max Four
210 mA
(DC Only)
Max Four
5 A Form A
Max Two
5 A Form A Max Two
10 A Form C
Max Six
5 A Form A
Optional Opto-isolated
22 I/O Plug-in Module
Digital Outputs
Add-on Board
(10 outputs)
Standard I/O
Plug-in Module
(6 in/6 out)
See the Setpoint Programming Mode Logic Diagram opposite.
The setpoint programming mode is entered by pressing the meters
and
buttons at the same time.
Setpoint Activation Values
Each setpoint activation value is individually programmed. Setpoint activation values can be set within the total span range of the meter and the selected input module.
Setpoint and Relay Control Settings See the Setpoint and Relay Control Settings diagram on Pages 42 and 43.
The control settings provide access to the following setpoint and relay functions for configuration using the meters 1st, 2nd, and 3rd digits:
1st Digit Relay Energize Functions.
2nd Digit Setpoint Activation Source.
3rd Digit Setpoint Delay, Timer, and Reset and Trigger Functions.
To enter press
buttons at the same time
and
Setpoint Programming Mode
Setpoint Activation Values
Enter these menus to set setpoint
(SP) activation values
[SP_1]
Setpoint 1 Default Setting = 180000
[SP_2]
Setpoint 2 Default Setting = 180000
[SP_3]
Setpoint 3 Default Setting = 50000
[SP_4]
Setpoint 4 Default Setting = 50000
[SP_5]
Setpoint 5 Default Setting = 100000
[SP_6]
Setpoint 6 Default Setting = 100000
Setpoint & Relay Control Function Settings
Enter these menus to configure SP control values
[SPC_1]
Setpoint 1
[SPC_2]
Setpoint 2
[SPC_3]
Setpoint 3
[SPC_4]
Setpoint 4
[SPC_5]
Setpoint 5
[SPC_6]
Setpoint 6
Setpoint Programming Mode Logic Diagram
Relay Energize Functions
All setpoints activate at the setpoint value.
All relays/setpoints are programmable to energize above or below the setpoint value.
Setpoint Activation Source
Setpoints activate from any input channel, selected meter register, or external switched inputs (digital input pins).
Setpoint Latching
Setpoints can be programmed in relay latching modes.
Setpoint Reset & Trigger Setpoints can be programmed to reset selected registers, or be manually reset. They can also trigger a data print or a data log.
SP-B
SP-A
Setpoint Tracking
Setpoint tracking can be applied to setpoints
configured in the hysteresis, deviation, or
PID modes.
Display Flashing
Display flashing can be applied to setpoints configured in the hysteresis or deviation modes.
Each setpoint can be programmed to make the display flash on and off while the setpoint is active, and keep it flashing until the setpoint de-activates.
Real-time Clock Option
Any setpoint can be programmed to operate from the real-time clock option.
Data Logging
Any setpoint can be programmed to log data within the meter (up to
4000 samples).
Data Printing to Serial Printer Any setpoint can be programmed to send data directly to a serial printer.
Data Printing to PC Any setpoint can be programmed to send data directly to a connected PC.
Hysteresis or Deviation
Each relay can operate in a hysteresis or deviation mode.
PID Control Settings
The PID (proportional, integral, derivative) control function provides exceptional control stability during control process applica-
tions. PID control is available from the following outputs:
Setpoint / relay output.
Analog output.
Relay and analog output at the same time.
PID control from the setpoint / relay output is available from SP1 and SP2 only.
There are two PID control outputs available via the analog output:
PID1 stored in register 50.
PID2 stored in register 51.
PID Control
Timer Modes
Each setpoint can be programmed to operate the relay in one of the following seven resident timer modes:
Normal Mode Timer
Single actuation, delay-on-make (DOM) and delay-onbreak (DOB).
Normally OFF/Pulsed ON Timers
Repeat ON Mode Timer multiple actuation, programmable offand on-time.
Pulse ON Mode Timer single actuation, programmable DOM and maximum on-time.
1-Shot ON Mode Timer single actuation, programmable DOM and minimum on-time.
Normally ON/Pulsed OFF Timers
Repeat OFF Mode Timer multiple actuation, programmable offand on-time.
Pulse OFF Mode Timer single actuation, programmable DOB and maximum off-time.
1-Shot OFF Mode Timer single actuation, programmable DOB and minimum off-time.
Hysteresis or Deviation
Each setpoint can be individually programmed to energize the relay in the hysteresis or deviation mode, with or without initial startup inhibit.
Hysteresis (deadband) is the programmable band above and below the setpoint value that determines when and for how long the relay is energized or de-energized. The setpoint can be programmed to energize the relay above or below the setpoint value.
The hysteresis setting can be any value between 0 and 65535 counts. The number of counts selected act both positively and negatively on the setpoint, forming a hysteresis band around the setpoint.
For example, if the setpoint setting is 500 counts and the hysteresis setting is 10 counts, the hysteresis band around the setpoint setting is 20 counts, starting at 490 counts and ending at 510 counts.
Note:
If hysteresis is set with ZERO counts, the relay energizes AT or ABOVE the setpoint value.
Deviation (passband) is the programmable band around the setpoint in which the setpoint can be programmed to energize the relay inside or outside the deviation band.
The deviation setting can be any value between 1 and 65535 counts. The number of counts selected act both positively and negatively on the setpoint, forming a deviation band around the setpoint.
For example, if the setpoint setting is 1000 counts and the deviation setting is 35 counts, the deviation band around the setpoint setting is 70 counts starting at 965 counts and ending at 1035 counts.
Initial Start-up Inhibit.
On power-on, start-up inhibit prevents the relay from energizing on the first setpoint activation cycle. Depending on how the meter has been programmed, initial start-up inhibit either functions during a falling input signal, or during a rising input signal.
Relay Time Control Modes The following time control mode settings can cover almost every relay timer application.
All setpoints can be individually programmed to operate a relay in one of the following time control modes above or below the setpoint value.
Normal Mode
This mode individually
programs a relays
setpoint with delayon-make (DOM) and
delay-on-break (DOB)
settings.
Normally OFF / Pulsed ON Modes These are delay modes were the relay is normally off and pulses on when the setpoint activates.
Repeat ON Mode
Multiple actuation, programmable on and
off time settings.
Pulse ON mode (Programmable ON-time)
Single actuation, programmable DOM and
on time settings.
1-Shot ON mode (Programmable Minimum ON-time)
Single actuation, programmable DOM and
minimum on time
settings.
Adj.
DOM
Normally ON / Pulsed OFF Modes These are delay modes were the relay is normally on and pulses off when the setpoint activates.
1-Shot OFF mode (Programmable Minimum OFF-time)
Single actuation, programmable minimum
off time and DOB settings.
Pulse OFF mode (Programmable OFF-time)
Single actuation, programmable off time
and DOB.
Repeat OFF Mode
Multiple actuation, programmable off and
on time settings.
Each setpoint can be individually configured for basic to advanced operations in the following three levels. Each operational level is designed to provide only the required relevant setpoint and relay functions.
The modes at Level 2 and Level 3 can be set to OFF for each individual setpoint, ensuring that no other functions are programmed to influence the setup.
Level 1
Setpoint & Relay Basic Mode
This is an easily programmable mode for users who require the
following basic setpoint and relay functions:
First Digit Relay Energize Functions
Relays programmed to energize above or below the setpoint value.
Second Digit SP Activation Source
Setpoints programmed to activate from selectable meter registers or one of six external switched inputs.
Third Digit Setpoint Latching
Relays programmed with latching and manual reset options.
Level 2
Setpoint & Relay Intermediate Mode
Level 2 uses all Level 1 functions and is further extended by the following programmable modes. The functionality of the relay energize functions are extended by allowing the relays to be programmed with or without initial start-up inhibit.
Hysteresis, Deviation & PID Mode
This mode adds extra functionality to the basic mode by providing programmable hysteresis or deviation settings for all setpoints, or PID control from setpoints SP1 and SP2.
Timer Modes
These modes add even more functionality to the basic and intermediate mode by providing each setpoint with a choice of one of seven resident programmable timers.
Level 3
Setpoint & Relay Advanced Mode
Level 3 uses all Level 1 and Level 2 functions combined with reset and trigger functions to provide an extremely powerful advanced mode.
Level 3 enables you to program all setpoints individually for operations normally requiring sophisticated controllers.
Example Procedure:
The following procedure describes how to program setpoint 1
(SP1) for the following Level 1 setpoint and relay functions:
See Setpoints and Relays Supplement (NZ201) for procedures to program all setpoint and relay operational levels (Level 1 to Level 3). (See page 3 for more information).
SP1 to activate from Channel 1 (CH1).
Relay to energize above or below SP1 value.
Relay to latch with manual relay reset.
From Step 5
T HERE STSTARART HERE
CONFIGURE
LEVEL 1
SETPOINT & RELAY
FUNCTIONS
Step 7
Save SP1
control settings
Example
Example
Step 9
Save SP1
control settings
Example
Step 5
To Step 6
Step 10
Programming tip
All required setpoint activation values (SP1 to SP6) can be adjusted before programming setpoint and relay control function settings. See Setpoint Programming Mode Logic Diagram on Page 42.
Setpoint & Relay Control Settings Diagram
The diagram below and continued on Page 43 shows the 1st, 2nd, and 3rd digit control settings for the setpoints and relays.
Programming Tip
PXX
Programming Tip
Programming Tip
A Tiger 320 Series meter has 6,144 registers which are provided for use by the operating system and the powerful Custom Macro Programming system (see page 11).
40 Manually Selectable Registers Using the front panel buttons, there are 40 registers that may be selected for use within the following functions:
[CodE_1] - Display Configuration [X50]. Selection of a register as the data source for displays, peak and valley, totalizers and analog outputs. (See pages 26 & 27)
Setpoint Control Settings [X1X]. Selection of a register
as the data source for a setpoint. (See Page 42)
Setpoint Control Settings [XX7]. Selection of a destination register that is to be reset by a setpoint with the contents of a selected source register. (See Page 43)
Setpoint Control Settings [XX7]. Select which registers contents are to be copied into the destination register by a setpoint. (See Page 43)
The 40 registers that can be selected as a data source, a reset source or a reset destination for the functions above are shown in the table on the right.
The table shows, in seven columns, the functions where these registers can be used.
Where a register is more likely to be used in a particular function, a closed circle (cid:4) is shown in the column. For those functions where a register is less likely to be used, an open circle (cid:2) is shown.
No register number is shown for the first 11 functions, because these 11 functions are identified in the display menu for direct selection by their code names.
When cycling through the Registers Menu and then Registers 1 to 244, the numerical Register Set will increment through each decade in turn, from 1 to 0, while the button is held down. When [200] is reached, [oFF] or [tArE] will be displayed. To select a specific number set, the button should be released and pressed again each time the left most decade displays the desired number for that decade.
To quickly exit the numerical 1 to 244 Register Set, hold the button down while cycling through the decades, and
release it when [oFF] or [tArE] appears.
Registers that Should Not be Used The following registers are contained within the selectable 1 to 244 Register Set, but they should not be selected because they are either reserved for future use, or for use by the operating system only:
15, 38, 47-48, 52-53, 61-64, 123-128, 140-141, 234-244
Resetting and Incrementing Using Setpoints Setpoints may be used to reset and/or increment registers. In the example shown on the right, 2 liter soft drink bottles are being filled and packed 12 to a case. Using the setpoint reset and increment feature, the number of bottles and the total number of filled cases is easily calculated and displayed.
Totalizer 1 counts from 0 to 2, resets, and repeats. CH 2 counts from 0 to 12, resets, and repeats.
Any selection of these Registers may cause a malfunction.
USING SETPOINTS TO INCREMENT AND RESET REGISTERS
Input Signal Pins 1 to 6 See the I-Series Input Modules Guide (Z87) for connection details of all input modules. On most single input signal conditioners, usually Pin 1 is the signal high pin (Hi +) and Pin 3 is the signal low pin (Lo ).
Function Pins Pins 8 to 15 Pin 8 Program Lock. By connecting the PROGRAM LOCK pin to the COMMON pin (pin 11 on the main PCB), the PROGRAM LOCK pin allows the meter's programmed parameters to be viewed but not changed.
Pin 9 Hold Reading. By connecting the HOLD READING pin to the COMMON pin (pin 11), the HOLD READING pin allows the
meter's display to be frozen. However, A/D conversions continue and as soon as pin 9 is disconnected from pin 11 the updated reading is instantly displayed.
Pin 10 Display Test and Reset. The DISPLAY TEST and RESET pin provides a test of the meter's display and resets the microprocessor when the DISPLAY TEST and RESET pin is connected to the COMMON pin (pin 11).
Pin 11 Common. To activate the HOLD, TEST and RESET, or LOCKOUT pins from the rear of the meter, the respective pins have to be connected to the COMMON pin.
Pins 14/15 AC/DC Power Input. These are the pins that supply power to the meter. See Power Supply for details of the standard and optional low voltage power supply.
Chassis Ground Tab. Only on versions with metal sheath casing.
Analog Outputs
Pin 16 Positive (+) analog output 1.
Pin 17 Negative () analog output 1 and 2.
Pin 18 Positive (+) analog output 2.
Serial Outputs RS-232 or RS-485
Ethernet The Ethernet carrier board has the same analog output pins, with 10/100Base-T Ethernet (RJ-45 Socket).
DeviceNet The DeviceNet carrier board has the same analog pinouts, but with a 3.5mm Pitch Socket. The serial output pins are replaced with DeviceNet pins, as follows:
Pin 19 - Positive (+) 24V.
Pin 20 - Can + (positive).
Pin 21 - N/C.
Pin 22 - Can - (negative).
Pin 23 - Negative (-) 24V.
Opto Isolated I/0 Module for External Breakout Box with 6 Outputs & 6 Inputs, or 16 Outputs & 6 Inputs
Relay Modules with up to two 5A Form A Relays, and up to two 10A Form C Relays
Relay Modules with up to 4 Independent 400V (210mA DC only) or (140mA AC/DC) SSRs
Relay Modules with five or six 5A Form A Relays
Open Collector / TTL / 5V Output
Relay Modules with up to four 5A Form A Relays
Flash Card Memory Module
Component Layout and External Devices Modular Construction
The Tiger 320 Series of 32-bit Programmable Meter Controllers incorporates, in one instrument, all the different functions required by todays automation and process control applications. This is made possible by modular construction, around standard case sizes, built to American, European, and Japanese standards.
The range comes with a wide variety of display options, including 5 or 6-digit numeric or alphanumeric displays, 6-digit LCD displays, and 51 or 101-segment red, green, or tri-color straight and circular bargraphs.
All meters are housed in one of three DIN case sizes, or the popular 4 ANSI case, and provide the ideal solution for your measurement and process control applications.
Modular construction ensures you dont have to pay for unnecessary hardware. Simply order the input and output options to suit your application.
Tiger 320 Series Modular Construction
Relay
Module
When Serial Outputs are not
required, the Standard Serial
Output Carrier Board is
available without Serial
Output to support
Relay Output Pins
32, 31, 30, 29, 28, 27, 26, 25
Flash Card
Memory Module
Part Numbers
OR91 & OR92
Flash Card
Two NPN Open
Collector Outputs
The Standard Serial Output, DeviceNet Output and
Ethernet Output Carrier
Boards accept all Relay and Logic I/O Modules
RS-232 or RS-485 Serial Output Pins, RJ-6 Socket Ethernet Output Carrier
Board has 10/100Base-T, with RJ-45 Socket
Analog
Output Pins
18, 17, 16
Optional
DeviceNet
Carrier Board
Single or Dual
Analog Output
Module
mA or Volts
Selection Header
DeviceNet Pins
24, 23, 22, 21, 20, 19
Input Signal
Conditioner
Analog
Output Pins
18, 17, 16
Input Signal
Conditioner
Pins 1, 2, 3
LOCK
HOLD
TEST
COMMON
CAPTURE
AC / DC
Power Pins
14, 15
Analog Outputs
and/or
Plug-in
Relay
& Logic
I/O Modules.
Serial
Output
Module
Single or Dual
Analog Output
Module
Display
Board
Processor
Board
Main
Board
Input Signal Conditioner
Processor
Board
Display Board
Analog Output Module PCB
Optional DeviceNet Carrier Board
Current or
Voltage
Selection
Header
CURRENT
Position
VOLTAGE
Position
Available in Single (0~4-20mA or 0-10V) or Dual (0-10V & 0-10V)
Standard Serial Output Modules RS-232 or RS-485
Note:
Externally mounted
Ethernet compatible
communication output
modules are available
that connect directly
to the standard (RS-
232 / RS-485) serial module outputs.
RS-485 Output Module PCB
RS-232 Output Module PCB
Opto Isolated I/O Modules Connect to External DIN Rail Mounting Breakout Box
10 Digital Outputs
Add-on Board
3M IDC
Cable
DIN Rail Mounting Breakout Box with Screw Terminal Blocks
Standard 6 Digital
Inputs/6 Digital Outputs
DIN Rail
Relay Module
Over 120 plug-in signal conditioning modules are available to suit almost any input signal, control, or data output. Modules can be easily inserted through the rear of the meter without disassembly of the case or removal from the panel. Many modules are exclusively designed for the Tiger 320 Series, and some can also be used with the Leopard and Lynx Family panel meters and bargraphs.
*Optimized for 50 Hz rejection. **Optimized for 60 Hz rejection.
Many additional input modules are available and others are constantly being developed. Check with your local distributor or see Texmates web site at: www.texmate.com for updated information. Pre calibrated I-Series Input Modules, that have span or zero potentiometers, can be interchanged between any I-Series compatible meter, without recalibration, because all of the analog scaling and reference circuitry is self-contained within the module. Where appropriate, all the standard ranges are designed to be header selectable by the user, and our unique SPAN ADJUST Header facilitates scaling to almost any required engineering unit. See Input Module Component Glossary for more information.
Unless otherwise specified, we will ship all modules pre calibrated with factory preselected ranges and/or scaling as shown in BOLD type. Other pre calibrated standard ranges or custom ranges may be ordered. Factory installed custom scaling and other custom options are also available.
Symbols Indicate Module Compatibility Within Meter Families
*A module code shown below a compatibility symbol indicates another module is available, similar in function, which may be more suited for use with that family.
**Modules which are compatible are listed below the Model Specific Symbol.
ALL MODELS
SOME MODELS MODEL SPECIFIC
Indicates a SMART MODULE. Smart Modules incorporate their own microprocessor and A/D converter. They communicate digitally with the Tiger 320 Operating System. Some also have their own SSR outputs.
IA02: AC Volts Scaled RMS, 200mV/2V/20V AC
IA12: AC Millivolt RMS Sigma Delta
ID01: DC Volts, 2/20/200V/Custom w/24V DC Exc
ID06: DC Volts 2/20/200/Custom V DC with External Decimal Select
ID08: DC Volts, 2/20/200/Custom V DC with External LIN Table Select
IDT2: Dual RTD Input, 2/3-wire, 100
IDP2: Dual Input, 3-wire RTD and 4-20mA
IDT3: Dual Input, 3-wire RTD and DCV
IDP3: Dual InputThermocouple (J/K/R/S/T/B/N)
and 4 to 20mA
IDR1: Dual Resistance Input, 0.2/2/20K
IDT6: Dual Input - Thermocouple and Load Cell 362C
IDD4: Dual Input, DCV and DCmV 2V/50mV DC
IF06: Line Frequency
IF10: Univ. Freq. / RPM / UP DOWN Counter
IDD6: Dual Input, DC mV and 4 to 20mA
TTL Input Connected to IF10
50mV/4 to 20mA DC
IDT1: Dual Thermocouple (J/K/R/S/T/B/N)
Tach Generator Connected to IF10
NAMUR Sensor Connected to IF10
IP10: Process + 3 Digital Inputs
PNP Open Collector Proximity Switch Connected to IF10
IOR1: ORP (Oxidation Reduction Potential)
Switch or Dry Contact Connected to IF10
Magnetic Pickup Connected to IF10
IQP1: Quad 4 to 20mA
IP09: 4-20mA with External LIN Table Select
IR01: Resistance, 2/3/4-Wire, 200/ 2K/20K
IS03: Pressure/Load Cell with AutoCal
5/10VDC Exc., 20/2mV/V, 4-wire
IS04: Pressure/Load Cell Ext Exc., 20/2mV/V, 4/6wire
IS05: Pressure/Load Cell 20/2mV/V, 5/10V Exc 4-wire
IS07: Pressure/Load Cell Ext Exc. High Impedance,
ITT1: Triple Thermocouple (J/K/R/S/T/B/N)
IT01: Thermocouple (J/K/R/S/T/B/N)
ITT4: Triple InputT/C, T/C (J/K/R/S/T/B/N)
and 4 to 20mA
IW03: DC-Watts, 10V/50mV DC
ITT8: Triple InputT/C (J/K/R/S/T/B/N),
4 to 20mA and 4 to 20mA
ITT9: Triple InputT/C (J/K/R/S/T/B/N), DCV and 50mV DC
ITP1: Triple 4 to 20mA
Dual input modules, and those modules exclusively compatible with the Leopard or Tiger Families, do not have zero and span adjustments. These modules are scaled and calibrated using the internal software functions of each individual meter.
Input and Output Pins On most modules Pin 1 is the Signal High input and Pin 3 is the Signal Low input. Typically Pin 2 is used for Excitation Voltage output.
24 V DC Output for 4-20 mA Header On some modules this header enables a 24 V DC 25 mA
(max) Excitation/Auxiliary output to be connected to Pin
2 that can power most 4-20 mA transmitters.
INPUT RANGE Headers
Range values are marked on the PCB. Typically two to eight positions are provided, which are selected with either a single or multiple jumper clip. When provided, a custom range position is only functional when the option has been factory installed.
SPAN Potentiometer (Pot)
If provided, the 15 turn SPAN pot is always on the right side (as viewed from the rear of the meter).
Typical adjustment is 20% of the input signal range.
SPAN ADJUST Header
This unique five-position header expands the adjustment range of the SPAN pot into five equal 20% steps, across 100% of the input Signal Span. Any input Signal Span can then be precisely scaled down to provide any required Display span from full scale to the smallest viewable unit.
Function Select Headers
On some modules various functions such as Amps and Volts, 4 wire and 6 wire, or cold junction compensation are selected by header positions that are marked on the PCB.
Excitation Output Select Headers When excitation outputs are provided, they are typically 5 V DC max 30 mA, 10 V DC max 30 mA (300 or higher resistance) or external supply. They are selected by either a single or multiple jumper clip.
ZERO Potentiometer (Pot)
If provided, the ZERO pot is always to the left of the SPAN pot (as viewed from the rear of the meter).
Typically it enables the input signal to be offset 5% of the full scale display span.
ZERO OFFSET RANGE Header When provided, this three position header increases the ZERO pots capability to offset the input signal, by 25% of the full scale display span. For example a Negative offset enables a 1 to 5 V input to display 0 to full scale. The user can select negative offset, positive offset, or no offset (ZERO pot disabled for two step non-interactive span and offset calibration).
SPAN RANGE Header
When this header is provided it works in conjunction with the SPAN ADJUST Header by splitting its adjustment range into a Hi and a Lo range. This has the effect of dividing the adjustment range of the SPAN pot into ten equal 10% steps across 100% of the input Signal Span.
ZERO ADJUST Header
When this header is provided, it works in conjunction with the ZERO OFFSET RANGE Header, and expands the ZERO pots offset capability into five equal negative steps or five equal positive steps. This enables virtually any degree of input signal offset required to display any desired engineering unit of measure.
PANEL CUTOUT
Case will mount in standard 1/8 DIN cutouts
SIDE VIEW
Straight-thru Connector
for meters with output board 20mm (0.79")
3.7mm
(0.15")
Mosaic Fitting
87.4mm
(3.45")
40.8mm
(1.61")
43.4mm
(1.71")
Snug Fitting
45 mm
(1.77")
43.4 mm
(1.71")
DIN Cutout spacers
40.8 mm
(1.61")
5.3 mm
(0.21")
117 mm
(4.61")
Right-angled Connector
11.8mm (0.47")
For extra strength in portable applications, the 8 DIN spacers should be snipped off and the Mosaic fitting cutout used. Alternatively, the High Strength Panel Mounting Kit (Part # OP-PMA96X48) can be used.
The 96x48mm case is particularly suitable for
mounting in mosaic panels or insulative panels up to 2" thick. They can also stack mount, 2 up in existing cutouts for 1/4 DIN
(96x96mm) or 4 up in 1/2 DIN (96X192mm).
4mm
(0.16")
8 places
3mm
(0.12")
8 places
1/8 DIN
Cutout spacers
91.6mm
(3.6")
92 mm
(3.62")
Loose Fitting
These dimensions are
increased by 1.6mm (0.06") when the metal surround case is installed.
TOP VIEW
Max. panel thickness
When extra panel mounting tightness is required, order the optional screw mount clip. P/N:(OP-MTLCLIP)
O-ring
Gasket
Base
Removable
Key-lock
Cover
Various bezel colors
are available.
Black is standard.
Clear Lockable
NEMA 4X
Splash Proof Cover
P/N:(OP-N4/96x48)
FRONT VIEW
1/8 DIN 96x48mm
96 mm
(3.78")
Safety
Catch
48 mm
(1.89")
3.9 mm
(0.15")
typical
For product details visit www.texmate.com
Local Distributor Address
Tel: 1-760-598-9899 USA 1-800-839-6283 Thats 1-800-TEXMATE Fax: 1-760-598-9828 Email: [email protected] Web: www.texmate.com
Texmate is an American manufacturer of high durability industrial grade panel meters, bar graphs, and transducers. Texmate's meters are frequently equipped with relays and various signal outputs for industrial automation applications and are known for their extremely long service life.